Fortinet 2 SXRC manual Sxrc Control Head Mounting Clips, Screws Here

Page 9

Once in place use the 2 supplied M3 flathead screws to secure the Trim Ring to the Metal Cage.

Trim Ring & Metal Cage Assembly

Front View

Mounting
Surface	Screws Here
	Screws Here

Mounting

Surface

Trim Ring & Metal Cage Assembly

Side View

The SXRC Control Head is held in place by two clips (one on each side) of the Plastic Trim Ring.

SXRC Control Head

Mounting Clips

Route the SXRC Control Head cable through one of the openings in the Trim Ring/Metal Cage assembly to your SXRC Interface Box location.

AMP1AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

*	kicker	*	ESC	HOME ENT
MEM-1	MEM-2 MEM-3	MEM-4

M1 M2 M3 M4

Press the SXRC control head in to the assembly until it locks into place.

AMP1AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

*	kicker	*	ESC	HOME ENT
MEM-1	MEM-2 MEM-3	MEM-4

M1 M2 M3 M4

Your SXRC Control Head is now mounted and you can move on to the wiring section of this manual

Installation

SXRC Remote Control

Image 9

Contents Page Sxrc SxrcSxrc Remote Control Sxrc Remote Control Kicker VFD Display Rubber Mounting Washers Includes fourESC Used to exit the current menu KeypadENT Used to enter the selected menu Home Used to return to the Main Menu and otherStandard DIN sized opening Be sure you will have a minimumOther surface panel to mount the Sxrc Screws Here Sxrc Control Head Mounting ClipsSurface Mounting With Screws Kicker Kicker 87654321 Run the supplied Blue-White Green-White Blue GreenOrange-White Brown-White Between each step Reconnect cablesPlease read Instructions and followPress the ENT key to enter the Main Default MenuMenu of the amplifier Press the UP or Down key untilAvve no Avve ye sVerriiffy ok SttoorreedPlace Did you check the pins #1 and #8 in the SX SeriesAmplifier to control then continue with Step If you have made your own cables double check them forIf you select Save YES then you choose which Global Press the ENT key to select InstallationUP or Down key to scroll through the options You want to use is selected press the ENT key toGo back and double check your Communications Network Inserted properly and ‘snapped’ into placeAre Straight-Through Ethernet Network cables By using the UP or Down key to scroll through ENT key to select InstallationAmplifiers to make sure they are not bent or damaged? Go back and double check your Communication NetworkAmplifiers to make sure they are not bent or damaged? Connected ...we can see Oklahoma Operation Navigation Sxrc Setup section of the manual This name to whatever you like. See the Sxrc Setup sectionYou! Plus...it is quicker than a Google search ManualDisplay will instantly show the current Down key to change the Drvc levelDrvc level .5 dB and each press Down key decreases the Drvc level .5 dBAmp addj MainAMP ADJ 1005 10 Otth chhnnsThrough frequency, boost/cut Requenc yLope Menu and choose another function to adjust OperationPress the ENT key to select HI-PASS menu and lower the high pass crossover pointLO-PASS menu and raise the low pass crossover point Menu and choose another function to adjustDegree or180 degree. Press the ESC Oth chhnnsBoth chns, left chn and right chn Use the UP or Down keys to select fromMute on or mute off. Press the ESC Through both chns, left chn and rightAdjustments in the Kompressor Menu the Komp indicator on the IsisRed-liinne While you are in the KompressorBypasss offf Function to adjustBypass OFF or Bypass on 8V Range or 16v rangeThrough noise off and noise on Remotte onThrough Remote on and Remote OFF Pink noise generatorWill either be the default name from Can be created in the Sxrc Setup menuGroup ADJ Any name you may have assigned toGain setting of this group, nothing will When you try to increase or decreaseExample AmpAdjustments in the Gain menu Display, the highest gain setting of the groupBoost/cut , bandwidth options menu. You Kicker uses a default QWhile in the frequency and slope options Indicates you are making adjustments in the HI-PASS menu Menu and choose another function to adjust Key to save your setting and return to the bothChns,left chn and right chn options Both chns,left chn and right chnChns, left chn and right chn options Both chns ,left chn and right chnTurn it OFF for this group If you select the KompressorEd-li n e Another group function to adjust1v raanngge Through from 24.0 db to-24.0 dBSick BAY Shooting and diagnostic toolsYou view each amplifier’s built in trouble Available tools in the Sick Bay menu areSelected amplifier’s current +12 volt Lock Viewing when you have multiple ampsReal time Same make or nameVoolltts Sx-50000//2Selected amplifier’s minimum +12 Volt terminal reading will be displayedSx -50000//2 =llo-voollt No hiissttoor ySelected amplifier’s total run time Reading will be displayed45 hr Ll ammppsThrough Select AMP or ALL Amps You can then use the UP or Down keys to Select Noise on or Noise OFF for»display All»autosearch »group amps»hold time »brightness »set time »temp. c/f»scrnsaver »led »set date »led TimeOff and auto Protected by the backup battery Default setting from Kicker is Level set in this menu. The default settingIntensity modes, On and Dim. When Keys are not being used they will dim toAutosearch function Return to the Sxrc Setup menu»group name »assign »release »link »remote vol »groupsRoouup More amplifiers available to assign Amplifiers you are wanting to useNo amplifiers currently assigned to that Select itGroup Amplifier will be displayedLink Off AMP ADJ »EQLink Off Group ADJ Link On AMP ADJExample When done selecting the current group’s Big baasssSet to Remote OFF Which character you want to change SxxrrcBass, center, front, rear, etc Sx-50000//2 EmmoorryAvve alll OaaddiinngEaarrcch AiitWhen the memory you want to use is selected By using the UP or Down key to scrollThrough the four memory locations Press the ENT key to storeErriiffy =0 AiilleedLoocckkeed KiicckkeerSecurity Again Press the ENT key to enter your lock codeRecalling a Preset Storing a Preset» EQ Sxrc Remote Control Power, Ground, Remote Internal Fusing in Sxrc Interface BoxOperating Voltage Remote Turn-On VoltageTo replace the fuse, first Disconnect the power harnessFrom the SX Interface Box Fuse Good Fuse Blown€ Blue LED off € Blue LED on, no display on Sxrc Control Head€ Blue LED on, garbage characters in display € Other problem, I am lost, I don’t know, Help € Everything powers up and looks great, just no sound†Select Remote Vol †Select OffAmplifier Help Amplifier Remote Address NameWhat is not COVERED? Today’s System Diagram Tomorrow’s System Diagram My Future ‘Drool’ System Cash Money Plan Pizza Delivery Earl’s Thoughts

Screws Here

SXRC Control Head

Mounting Clips

kicker

SXRC Remote Control