One for All 6-Device Universal Remote Using Learning, Programming Favorite Channel Scan

Page 13

OFA 6L with Learning Owners Manual.fm Page 12 Thursday, February 17, 2005 1:10 PM

ONE FOR ALL 6L UNIVERSAL REMOTE CONTROL WITH LEARNING

3.To stop scanning channels at any time, press any key once.

PROGRAMMING FAVORITE CHANNEL SCAN

In the TV, VCR, DVD or CBL/SAT mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when you press FAV (see “Using Channel Scan” on page 11).

NOTE: Only channels of one mode can be stored for Favorite Channel Scan.

1.On the remote control, press TV, VCR,

DVD or CBL/SAT once.

2.Press and hold SET until the LED (red light) blinks twice, then release SET.

3.Enter 9 9 6. The LED will blink twice.

4.Use the keypad to enter a favorite channel number (e.g., 031). Then press SET once.

NOTE: If the original remote control required pressing an ENTER key to change the channel, also press the ENTER key after the channel number (e.g., 0 3 1 ENTER).

5.If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels.

NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming.

6.To exit programming, press and hold SET for 3 seconds. The LED will blink twice.

USING LEARNING

The One For All 6L Universal Remote Control with Learning (URC-6820 B00)

includes a Learning feature so you can add functions that are unique to your home entertainment devices (e.g., DVD EJECT). However, there are some considerations.

LEARNING PRECAUTIONS

•Your original remote controls must be in working order for learning to work properly.

•Learned keys are mode specific, so each one can store a unique function for each mode.

•Learned keys can be used in macros (see “Using Macros” on page 9).

•Do not use the following keys for learning: Device Keys, SETUP, FAV, or Record (•) Key.

•Learning capacity is approximately 50 to 70 keys, depending on the code being learned.

•If both learned and keymoved functions are assigned to the same key, the last programmed function is stored.

•A learned function cannot be used as a source for Keymover (see “Using Keymover” on page 14).

•Certain device codes are not learnable including multi-frequency types, some high frequency ones, and other unusual formats.

•For optimum learning, avoid high levels of ambient light such as natural sunlight or energy-efficient fluorescent lights.

NOTE: Please have your original remote controls handy before programming learning. Be sure to press each teaching key within 5 seconds of the previous entry. Otherwise, the One For All 6L Universal Remote Control with

12 Programming Favorite Channel Scan

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Table of Contents Features and Functions ONE for ALL 6L Universal Remote Control with LearningIntroduction IntroductionKEY Charts Features and FunctionsSound.Use Lower.UseUse the Transport 009 orPress REC to record a DVD or VCR program Device KEY Controls These Devices Device TableOn the remote controls back, push Installing BatteriesSlide the battery cover out Obtain two 2 new AAA alkalineSetting Up Your Components Setting UP Your ComponentsTV Code Brand Name VCR Code PVR Code CBL/SAT CodeProgramming Combo Device Control Searching for Your CodeProgramming Combo Device Control SETPower Using MacrosChecking the Codes Enter 9 9 0. The LED will blink twiceTo Operate Master Power Macro Using MacrosProgramming a Macro on a Device KEY Using Channel Scan Using Channel ScanTo Program the Device Key Macro To Operate the Device Key MacroLearning Precautions Using LearningProgramming Favorite Channel Scan Programming Favorite Channel ScanRe-assigning Device Keys RE-ASSIGNING Device KeysProgramming a Learning KEY Deleting Functions from the Learning KeysUsing Keymover Using KeymoverUnlock Changing Volume LockUpgrade Exclusions TroubleshootingAbout Upgrading About UpgradingTroubleshooting FCC Compliance Limited WarrantyFCC Compliance Additional Information Additional InformationOne For All 330 URC-682001/0520 Índice de Materias Control with LearningCaracterísticas Y Funciones IntroducciónIntroducción Funciones DE LAS Teclas Características y FuncionesUse las Teclas de Use Para subir/ bajar el Volumen.UseONE for ALL 6L Universal Remote Control with Learning Tabla DE Dispositivos Instalación de las Baterías BateríasNuevas y colóquelas en el + y en el interiorProgramación de un Dispositivo Aparato Programación DE UN Dispositivo AparatoProgramación DE UN Aparato Combinado Búsqueda DE SU CódigoProgramación de un Aparato Combinado Encienda el aparato combinado TV/ DVD e inserte un DVDVerificación de los Códigos Verificación DE LOS CódigosProgramación DE UN Macro DE Canal Favorito Uso de los MacrosIntroduzca 9 9 5. El LED parpadeará dos veces Presione CBL/SAT una vez Introduzca el número del canal 5Para Programar el Macro de Tecla de Dispositivo Uso del Macro de Encendido Maestro en la Tecla PowerDVD Uso de la Exploración de Canales Control with Learning USO DE LA Exploración DE CanalesBorrar UN Macro Presione TV, VCR, o CBL/SAT una vez Presione FAV una vezUso de la Función Aprendizaje USO DE LA Función AprendizajePresione TV, VCR, DVD o CBL/SAT una vez Reasignación de las Teclas de Dispositivos Reasignación DE LAS Teclas DE DispositivosProgramación DE UNA Tecla DE Aprendizaje Borrar Funciones DE LAS Teclas DE AprendizajeUso de la Función Keymover USO DE LA Función KeymoverCambio del Bloqueo del Volumen Cambio DEL Bloqueo DEL VolumenRestauración DE LOS Valores Fijados EN LA Fábrica Acerca DE LA ActualizaciónRestauración de los Valores Fijados en la Fábrica Parámetros DE FábricaLocalización de Fallas Localización DE FallasVolumen con el remoto Problema Traté el método deDel Volumen en la Desbloquear el volumenConformidad con la FCC Garantía LimitadaLunes a Viernes de 9AM to 5PM ET Tiempo del Este Información Adicional Información Adicional
Top Page Image Contents