One for All 6-Device Universal Remote owner manual Changing Volume Lock, Unlock

Page 16

OFA 6L with Learning Owners Manual.fm Page 15 Thursday, February 17, 2005 1:10 PM

CHANGING VOLUME LOCK

The One For All 6L Universal Remote Control with Learning (URC-6820 B00) is set at the factory for independent volume control of each selected device.

However, you may change the Volume Lock setting to Global Volume Lock so that a device’s volume will be locked to one mode (e.g., to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.

LOCKING VOLUME CONTROL TO ONE MODE (GLOBAL VOLUME LOCK)

1.Press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 9 3 and then press any mode key once (e.g., TV). The LED will blink twice.

3.Now, when you press VOL +, VOL -, or MUTE, the volume of the selected device (e.g., TV) will be controlled regardless of the mode you have selected.

UNLOCKING VOLUME CONTROL FOR A

SINGLE DEVICE (INDIVIDUAL VOLUME

UNLOCK)

1.After performing Global Volume Lock (see left), press a desired mode key where you want volume to be unlocked (e.g., AUD) and controlled within its own mode.

2.Press and hold SET until the LED (red light) blinks twice, then release SET.

3.Enter 9 9 3 and then press VOL - once. The LED will blink four times.

OWNERS MANUAL

4.If desired, repeat steps 1 through 3 (of this section) for each device that you want volume to be unlocked.

5.Now, after you select a device that has volume unlocked (e.g., AUD), pressing

VOL +, VOL -, or MUTE, will control the device’s volume only in its own mode.

UNLOCKING ALL VOLUME CONTROL (RESTORING DEFAULT SETTING)

NOTE: Performing these instructions will restore independent volume control for all programmed devices (e.g., TV volume control in TV mode, VCR volume in VCR mode, etc.).

1.On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 9 3 and then press VOL + once. The LED will blink four times.

3.Volume will again be independently controlled according to its default states for all programmed devices.

RESTORING FACTORY DEFAULT SETTINGS

The One For All 6L Universal Remote Control with Learning (URC-6820 B00) includes a Setup Code Reset program. You can use it to restore all your programmed codes to factory settings and delete all custom programming.

IMPORTANT: Executing this program erases all code settings and all custom settings including, Macros, Learned Keys, Reassigned Device Keys, Keymoved Keys, Favorite Channels, and all device settings.

Changing Volume Lock 15

Image 16
Contents Page Table of Contents ONE for ALL 6L Universal Remote Control with Learning Features and FunctionsIntroduction IntroductionFeatures and Functions KEY ChartsSound.Use Lower.UseUse the Transport 009 orPress REC to record a DVD or VCR program Device Table Device KEY Controls These DevicesInstalling Batteries On the remote controls back, pushSlide the battery cover out Obtain two 2 new AAA alkalineSetting UP Your Components Setting Up Your ComponentsTV Code Brand Name VCR Code PVR Code CBL/SAT CodeSearching for Your Code Programming Combo Device ControlProgramming Combo Device Control SETUsing Macros PowerChecking the Codes Enter 9 9 0. The LED will blink twiceTo Operate Master Power Macro Using MacrosProgramming a Macro on a Device KEY Using Channel Scan Using Channel ScanTo Program the Device Key Macro To Operate the Device Key MacroUsing Learning Learning PrecautionsProgramming Favorite Channel Scan Programming Favorite Channel ScanRE-ASSIGNING Device Keys Re-assigning Device KeysProgramming a Learning KEY Deleting Functions from the Learning KeysUsing Keymover Using KeymoverChanging Volume Lock UnlockTroubleshooting Upgrade ExclusionsAbout Upgrading About UpgradingTroubleshooting FCC Compliance Limited WarrantyFCC Compliance Additional Information Additional InformationOne For All 330 URC-682001/05Control with Learning 20 Índice de MateriasCaracterísticas Y Funciones IntroducciónIntroducción Características y Funciones Funciones DE LAS TeclasUse Para subir/ bajar el Volumen.Use Use las Teclas deONE for ALL 6L Universal Remote Control with Learning Tabla DE Dispositivos Baterías Instalación de las BateríasNuevas y colóquelas en el + y en el interiorProgramación DE UN Dispositivo Aparato Programación de un Dispositivo AparatoBúsqueda DE SU Código Programación DE UN Aparato CombinadoProgramación de un Aparato Combinado Encienda el aparato combinado TV/ DVD e inserte un DVDVerificación DE LOS Códigos Verificación de los CódigosUso de los Macros Programación DE UN Macro DE Canal FavoritoIntroduzca 9 9 5. El LED parpadeará dos veces Presione CBL/SAT una vez Introduzca el número del canal 5Para Programar el Macro de Tecla de Dispositivo Uso del Macro de Encendido Maestro en la Tecla PowerDVD Control with Learning USO DE LA Exploración DE Canales Uso de la Exploración de CanalesBorrar UN Macro Presione TV, VCR, o CBL/SAT una vez Presione FAV una vezUso de la Función Aprendizaje USO DE LA Función AprendizajePresione TV, VCR, DVD o CBL/SAT una vez Reasignación DE LAS Teclas DE Dispositivos Reasignación de las Teclas de DispositivosProgramación DE UNA Tecla DE Aprendizaje Borrar Funciones DE LAS Teclas DE AprendizajeUSO DE LA Función Keymover Uso de la Función KeymoverCambio DEL Bloqueo DEL Volumen Cambio del Bloqueo del VolumenAcerca DE LA Actualización Restauración DE LOS Valores Fijados EN LA FábricaRestauración de los Valores Fijados en la Fábrica Parámetros DE FábricaLocalización DE Fallas Localización de FallasProblema Traté el método de Volumen con el remotoDel Volumen en la Desbloquear el volumenConformidad con la FCC Garantía LimitadaLunes a Viernes de 9AM to 5PM ET Tiempo del Este Información Adicional Información Adicional