One for All 6-Device Universal Remote Setting UP Your Components, Setting Up Your Components

Page 8

OFA 6L with Learning Owners Manual.fm Page 7 Thursday, February 17, 2005 1:10 PM

4.Test the remote control by first pressing POWER and then any mode key (e.g., TV). If the batteries are inserted correctly, the LED (red light) will blink once.

NOTE: When batteries are low, the remote control will blink 5 times after each key press. The remote will stop operating when the batteries need replacement. The permanent memory retention ensures that your codes are stored permanently even during battery replacement.

SETTING UP YOUR

COMPONENTS

The One For All 6L Universal Remote Control with Learning (URC-6820 B00) is preprogrammed at the factory to operate a Sony TV, DVD and VCR, a Motorola Cable Box, a Sony Tivo PVR/DVR, and a Pioneer Receiver. To control devices other than the default brands, perform the following steps; otherwise skip this section.

NOTE: For Combo Device control, see the next section.

1.Turn on a device (e.g., TV, VCR or DVD player) and, if applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding. Highlight or write down the codes and device you wish to program before starting step 2.

2.On the remote control, press a device key once (i.e., TV, CBL/SAT, VCR, DVD, PVR, or AUD).

3.Press and hold SET until the LED (red light) blinks twice, then release SET.

4.Use the “Manufacturer’s Codes (Códigos del Fabricante)” (starting on page 42) to locate the type of device

OWNER’S MANUAL

and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter the same code again.

5.Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still doesn’t work, try “Searching for Your Code” on page 8.

NOTE: If the device does not have a POWER

key, press the (PLAY) key.

6.Repeat steps 1 through 5 for each device you want to control. For future reference, write down each working device code in the following boxes:

TV Code:

Brand Name:_____________________

VCR Code:

Brand Name:_____________________

PVR Code:

Brand Name:_____________________

CBL/SAT Code:

Brand Name:_____________________

DVD Code:

Setting Up Your Components 7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Page Table of Contents ONE for ALL 6L Universal Remote Control with Learning Features and FunctionsIntroduction IntroductionFeatures and Functions KEY ChartsSound.Use Lower.UsePress REC to record a DVD or VCR program 009 orUse the Transport Device Table Device KEY Controls These DevicesInstalling Batteries On the remote controls back, pushSlide the battery cover out Obtain two 2 new AAA alkalineSetting UP Your Components Setting Up Your ComponentsTV Code Brand Name VCR Code PVR Code CBL/SAT CodeSearching for Your Code Programming Combo Device ControlProgramming Combo Device Control SETUsing Macros PowerChecking the Codes Enter 9 9 0. The LED will blink twiceProgramming a Macro on a Device KEY Using MacrosTo Operate Master Power Macro Using Channel Scan Using Channel ScanTo Program the Device Key Macro To Operate the Device Key MacroUsing Learning Learning PrecautionsProgramming Favorite Channel Scan Programming Favorite Channel ScanRE-ASSIGNING Device Keys Re-assigning Device KeysProgramming a Learning KEY Deleting Functions from the Learning KeysUsing Keymover Using KeymoverChanging Volume Lock UnlockTroubleshooting Upgrade ExclusionsAbout Upgrading About UpgradingTroubleshooting FCC Compliance Limited WarrantyFCC Compliance Additional Information Additional InformationOne For All 330 URC-682001/05Control with Learning 20 Índice de MateriasIntroducción IntroducciónCaracterísticas Y Funciones Características y Funciones Funciones DE LAS TeclasUse Para subir/ bajar el Volumen.Use Use las Teclas deONE for ALL 6L Universal Remote Control with Learning Tabla DE Dispositivos Baterías Instalación de las BateríasNuevas y colóquelas en el + y en el interiorProgramación DE UN Dispositivo Aparato Programación de un Dispositivo AparatoBúsqueda DE SU Código Programación DE UN Aparato CombinadoProgramación de un Aparato Combinado Encienda el aparato combinado TV/ DVD e inserte un DVDVerificación DE LOS Códigos Verificación de los CódigosUso de los Macros Programación DE UN Macro DE Canal FavoritoIntroduzca 9 9 5. El LED parpadeará dos veces Presione CBL/SAT una vez Introduzca el número del canal 5DVD Uso del Macro de Encendido Maestro en la Tecla PowerPara Programar el Macro de Tecla de Dispositivo Control with Learning USO DE LA Exploración DE Canales Uso de la Exploración de CanalesBorrar UN Macro Presione TV, VCR, o CBL/SAT una vez Presione FAV una vezPresione TV, VCR, DVD o CBL/SAT una vez USO DE LA Función AprendizajeUso de la Función Aprendizaje Reasignación DE LAS Teclas DE Dispositivos Reasignación de las Teclas de DispositivosProgramación DE UNA Tecla DE Aprendizaje Borrar Funciones DE LAS Teclas DE AprendizajeUSO DE LA Función Keymover Uso de la Función KeymoverCambio DEL Bloqueo DEL Volumen Cambio del Bloqueo del VolumenAcerca DE LA Actualización Restauración DE LOS Valores Fijados EN LA FábricaRestauración de los Valores Fijados en la Fábrica Parámetros DE FábricaLocalización DE Fallas Localización de FallasProblema Traté el método de Volumen con el remotoDel Volumen en la Desbloquear el volumenLunes a Viernes de 9AM to 5PM ET Tiempo del Este Garantía LimitadaConformidad con la FCC Información Adicional Información Adicional
Top Page Image Contents