One for All 6-Device Universal Remote RE-ASSIGNING Device Keys, Re-assigning Device Keys

Page 14

OFA 6L with Learning Owners Manual.fm Page 13 Thursday, February 17, 2005 1:10 PM

Learning (URC-6820 B00) exits the learning mode.

PROGRAMMING A LEARNING KEY

1.Press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 7 5. The LED will blink twice.

3.Press a device key once (e.g., TV) to assign a mode for learning.

4.Press the desired key once (e.g., +100) to store a feature to be learned. The LED will turn on and remain on for 5 seconds. If the LED does not turn on, go back to step 1 and start again.

5.Place your original remote control (e.g., TV remote control) head-to-head (about 2" apart) from the One For All 6L Universal Remote Control with Learning (URC-6820 B00).

6.On your original remote control, press and hold the key (i.e., feature) to be learned until the LED on the One For All 6L Universal Remote Control with Learning (URC-6820 B00) turns off and then blinks twice. If the LED does not blink twice, repeat steps 3 through 6.

7.To learn functions onto other learning keys (e.g., M1 and M2), repeat steps 3 through 6.

8.To lock in new feature(s) on the One For All 6L Universal Remote Control with Learning (URC-6820 B00), press and hold SET until the LED blinks twice, then release SET.

9.To test a learned feature, press a device key (e.g., TV) once where the learning mode was assigned. Then press the learning key (e.g., +100) where the learned feature is stored.

OWNER’S MANUAL

DELETING FUNCTIONS FROM THE LEARNING KEYS

1.Press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 7 6. The LED will blink twice.

3.Press the device key once where the learned feature is stored (e.g., TV).

4.Press the learning key (e.g., +100) to be deleted twice. The LED will blink twice after the second press.

5.To clear additional functions stored on other learning keys, repeat steps 1 through 4 (in this section).

RE-ASSIGNING DEVICE KEYS

You can set the One For All 6L Universal Remote Control with Learning (URC-6820 B00) to control a second TV, SAT, DVD player, or other device. For example, to control a TV, a cable box, and two DVDs, you will need to re-assign an unused device key (i.e., VCR) to operate the second DVD as follows:

1.On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET.

2.Enter 9 9 2. The LED will blink twice.

3.Press DVD once, then press VCR once.

4.The VCR key is now ready to be programmed for your second DVD. See “Setting Up Your Components” on page 7.

To re-assign other device keys to the VCR key, repeat steps 1 through 4 by substituting the sequence from the below chart:

To Re-Assign

Perform Sequence

Device

 

 

 

Re-assigning Device Keys 13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page Table of Contents Introduction ONE for ALL 6L Universal Remote Control with LearningFeatures and Functions IntroductionSound.Use Features and FunctionsKEY Charts Lower.UsePress REC to record a DVD or VCR program 009 orUse the Transport Device Table Device KEY Controls These DevicesSlide the battery cover out Installing BatteriesOn the remote controls back, push Obtain two 2 new AAA alkalineTV Code Brand Name VCR Code PVR Code Setting UP Your ComponentsSetting Up Your Components CBL/SAT CodeProgramming Combo Device Control Searching for Your CodeProgramming Combo Device Control SETChecking the Codes Using MacrosPower Enter 9 9 0. The LED will blink twice Programming a Macro on a Device KEY Using Macros To Operate Master Power Macro To Program the Device Key Macro Using Channel ScanUsing Channel Scan To Operate the Device Key MacroProgramming Favorite Channel Scan Using LearningLearning Precautions Programming Favorite Channel ScanProgramming a Learning KEY RE-ASSIGNING Device KeysRe-assigning Device Keys Deleting Functions from the Learning KeysUsing Keymover Using KeymoverChanging Volume Lock UnlockAbout Upgrading TroubleshootingUpgrade Exclusions About UpgradingTroubleshooting FCC Compliance Limited WarrantyFCC Compliance One For All 330 Additional InformationAdditional Information URC-682001/05Control with Learning 20 Índice de MateriasIntroducción IntroducciónCaracterísticas Y Funciones Características y Funciones Funciones DE LAS TeclasUse Para subir/ bajar el Volumen.Use Use las Teclas deONE for ALL 6L Universal Remote Control with Learning Tabla DE Dispositivos Nuevas y colóquelas en el BateríasInstalación de las Baterías + y en el interiorProgramación DE UN Dispositivo Aparato Programación de un Dispositivo AparatoProgramación de un Aparato Combinado Búsqueda DE SU CódigoProgramación DE UN Aparato Combinado Encienda el aparato combinado TV/ DVD e inserte un DVDVerificación DE LOS Códigos Verificación de los CódigosIntroduzca 9 9 5. El LED parpadeará dos veces Uso de los MacrosProgramación DE UN Macro DE Canal Favorito Presione CBL/SAT una vez Introduzca el número del canal 5DVD Uso del Macro de Encendido Maestro en la Tecla PowerPara Programar el Macro de Tecla de Dispositivo Borrar UN Macro Control with Learning USO DE LA Exploración DE CanalesUso de la Exploración de Canales Presione TV, VCR, o CBL/SAT una vez Presione FAV una vezPresione TV, VCR, DVD o CBL/SAT una vez USO DE LA Función AprendizajeUso de la Función Aprendizaje Programación DE UNA Tecla DE Aprendizaje Reasignación DE LAS Teclas DE DispositivosReasignación de las Teclas de Dispositivos Borrar Funciones DE LAS Teclas DE AprendizajeUSO DE LA Función Keymover Uso de la Función KeymoverCambio DEL Bloqueo DEL Volumen Cambio del Bloqueo del VolumenRestauración de los Valores Fijados en la Fábrica Acerca DE LA ActualizaciónRestauración DE LOS Valores Fijados EN LA Fábrica Parámetros DE FábricaLocalización DE Fallas Localización de FallasDel Volumen en la Problema Traté el método deVolumen con el remoto Desbloquear el volumenLunes a Viernes de 9AM to 5PM ET Tiempo del Este Garantía LimitadaConformidad con la FCC Información Adicional Información Adicional
Top Page Image Contents