EverFocus EDSR100H instruction manual Installation

Page 18

INSTALLATION

5.Installation

(1)Insert a HDD (IDE) for Video Storage

The HDD should be set as MASTER.

( Normally the default setting of HDD is Master)

Notice: After the hard disk case is inserted into the hard disk tray, be sure to Turn the tray key in lock position. Otherwise, hard disk will not be detected and The System Loading procedure can not be completed.

(2)Connect cable for video/audio input and video/audio out, The POWER LED lights if power is normal.

(3)Switch Power On

The detail connection is described in SYSTEM CONNECTION .

(4)	MENU	Press MENU key to enter SET UP MENU.
		Once inside the main menu you will find there are
		nine set up pages as below:
	1.	CLOCK/LANGUAGE SETTING MENU
	2.	DAYLIGHT SAVE SETTING MENU
	3.	TIMER SETTING MENU
	4.	NORMAL RECORD SETTING MENU
	5.	ALARM RECORD SETTING MENU
	6.	BUZZER SETTING MENU
	7.	ARCHIVE SETTING MENU
	8.	RS232/RS485 SETTING MENU
	9.	SYSTEM SETTING MENU

(5)	Turn the jog dial clockwise or counterclockwise to change set up page.

Image 18

Contents EDSR100H Safety Precautions Safety Warning AC100V~240V Power Cords Important Safeguards Important SafeguardsTable of Contents Product Overview and Features Product OverviewSpecifications Front Panel Keypads Front Panel KeypadsLeft/Right Button Press Up/Down Button Press Display Press this key to switch ON/OFF Jog and Shuttle DialBack Panel Connections PowerBack Panel Connections AudioAlarm Input/ Output MonitorVideo in /Output RS232 System Connection System ConnectionOne Camera Connection Multiplexer VCR Multiplexer ConnectionMain Monitor Multiplexer VCR Out Multiplexer Main Monitor OutputQuad VCR Quad Connection. Quad with VCR in VCR out connectorMain Monitor Quad VCR Out Quad Main Monitor OutQuad connection. Quad without VCR in VCR out connector Main Monitor Quad Video Out to Video RecorderInstallation Menu Date 2003/04/24 TUE Time CLOCK/ Language Setting MenuVersion 1.0 2003/05/26 CLOCK/LANGUAGE Setting Menu , we SET Menu Language EnglishFrom 0000 to Daylight Setting MenuFrom 0000 to Daylight Setting Menu , we define END on JAN 1ST MONStandard OFF SUN Timer Setting MenuTimer Setting Menu Week Start Stop Speed Quality SET SUN Standard OFFSpeed SETNormal Record Setting Menu Normal Recording MENU, we defineMultiplexer Disk FullPRE-ALARM Operation Recording Speed Alarm Record Setting MenuAlarm Record Setting Menu Alarm Operation Recording Speed Recording QualityAlarm Reset Type PRE-ALARM OperationPRE Alarm Time 15Figure 1 Alarm out Normally open connection use pin # 13 and #Normally Closed Connection use pin # 13 and # Alarm AlarmAlarm in and alarm reset CircuitBuzzer Setting Menu Record720x576 Archive Setting MenuArchive Setting Menu Picture Size Time StampRS232/RS485 Setting Menu Baud RateParity None Data BIT Stop BIT Password System Setting MenuSystem Setting Menu Play with Audio Password Enable OFFPress no to renew HDD and Press Enter key to Exit Press Yes to Renew HDD and Press Enter key to ExitCF Renew Press Record key to start the recording immediately RecordingInstant Recording REC StopRecording Setting Menu Recording Operation Alarm RecordingPress Menu key and turn the jog dial to select the Alarm MenuPlay Playing BackNormal Playback REV.PLAYSlow Forward/Reverse Playback PauseFrame/Field advance Forward/Reverse Search Playback Segment Search PlaybackSearch Alarm Search Playback Date/Time Search Playback Press the Play key to start playing back CopyStill Image Copy Press the Pause key to freeze the pictureCopy to Movie File Press Copy key and then the copy menu appearsCopy Copy to Movie File Pause Search Stop Transmission setting Interface SpecificationsSUB 9-pin connector specifications Pin assignment of the 9-pin D-SUB connectorRemote Control Protocol Receiver ID Digital Video Recorder Page Remote Controller Remote ControllerAPPENDIX- A/Time Lapse Mode Recording Time Appendix-AWhen Recording with 160-GB HDD APPENDIX-B/SECURITY Lock Setting Appendix-BLock Japan Office Head OfficeUSA Office Beijing Office