EverFocus EDSR100H instruction manual AC100V~240V Power Cords

Page 4

Safety Precautions

Safety Precautions

The lightning flash with an arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated ” dangerous voltage ” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons

The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance(servicing)instructions in the literature accompanying the appliance.

Warning :

To prevent fire or shock hazard, do not expose units not specifically designed for outdoor use to rain or moisture.

Attention:

Installation should be performed by qualified service personnel only

in accordance with the National Electrical Code or applicable local codes.

Power Disconnect:

Units with or without ON -OFF switches have power supplied to the unit whenever the power code is inserted into the power source; however, the unit is operational only when the ON-OFF switch is in the ON position.

The power cord is the main power disconnect for all units.

External Power Supplies

Use only the recommended power supplies.

Power supplies must comply with the requirement of

the latest version of IEC 60065/CNS 13439. Substitutions may damage the unit or cause a fire or shock hazard

Warning:

Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid electrostatic discharge.

Service

If the unit ever needs repair service, the customer should contact the nearest Everfocus Electronics Corp. Service Center for return authorization and shipping instruction.

AC100V~240V Power Cords

AC100V~240V power cords

Image 4
Contents EDSR100H Safety Precautions Safety Warning AC100V~240V Power Cords Important Safeguards Important SafeguardsTable of Contents Product Overview and Features Product OverviewSpecifications Front Panel Keypads Front Panel KeypadsLeft/Right Button Press Up/Down Button Press Display Press this key to switch ON/OFF Jog and Shuttle DialPower Back Panel ConnectionsBack Panel Connections AudioMonitor Alarm Input/ OutputVideo in /Output RS232 System Connection System ConnectionOne Camera Connection Multiplexer Connection Main Monitor Multiplexer VCR OutMultiplexer VCR Multiplexer Main Monitor OutputQuad Connection. Quad with VCR in VCR out connector Main Monitor Quad VCR OutQuad VCR Quad Main Monitor OutQuad connection. Quad without VCR in VCR out connector Main Monitor Quad Video Out to Video RecorderInstallation Menu CLOCK/ Language Setting Menu Version 1.0 2003/05/26 CLOCK/LANGUAGE Setting Menu , we SETDate 2003/04/24 TUE Time Menu Language EnglishDaylight Setting Menu From 0000 to Daylight Setting Menu , we defineFrom 0000 to END on JAN 1ST MONTimer Setting Menu Timer Setting Menu Week Start Stop Speed Quality SET SUNStandard OFF SUN Standard OFFSpeed SETNormal Record Setting Menu Normal Recording MENU, we defineMultiplexer Disk FullAlarm Record Setting Menu Alarm Record Setting Menu Alarm Operation Recording SpeedPRE-ALARM Operation Recording Speed Recording QualityPRE-ALARM Operation Alarm Reset TypePRE Alarm Time 15Figure 1 Normally open connection use pin # 13 and # Alarm outNormally Closed Connection use pin # 13 and # Alarm Alarm in and alarm resetAlarm CircuitBuzzer Setting Menu RecordArchive Setting Menu Archive Setting Menu Picture Size720x576 Time StampBaud Rate RS232/RS485 Setting MenuParity None Data BIT Stop BIT System Setting Menu System Setting Menu Play with Audio Password EnablePassword OFFPress no to renew HDD and Press Enter key to Exit Press Yes to Renew HDD and Press Enter key to ExitCF Renew Recording Instant RecordingPress Record key to start the recording immediately REC StopAlarm Recording Press Menu key and turn the jog dial to select the AlarmRecording Setting Menu Recording Operation MenuPlaying Back Normal PlaybackPlay REV.PLAYPause Slow Forward/Reverse PlaybackFrame/Field advance Forward/Reverse Segment Search Playback Search PlaybackSearch Alarm Search Playback Date/Time Search Playback Copy Still Image CopyPress the Play key to start playing back Press the Pause key to freeze the picturePress Copy key and then the copy menu appears Copy to Movie FileCopy Copy to Movie File Pause Search Stop Interface Specifications SUB 9-pin connector specificationsTransmission setting Pin assignment of the 9-pin D-SUB connectorRemote Control Protocol Receiver ID Digital Video Recorder Page Remote Controller Remote ControllerAPPENDIX- A/Time Lapse Mode Recording Time Appendix-AWhen Recording with 160-GB HDD Appendix-B APPENDIX-B/SECURITY Lock SettingLock Head Office USA OfficeJapan Office Beijing Office