EverFocus EDSR100H instruction manual Press no to renew HDD and Press Enter key to Exit

Page 35

MENU

(4)FIELD CODE LINE : When the system is connected to the Multiplexer, it is used to adjust the field code of the Multiplexer.

The values: 00~20

The default value is 13, it is suitable for most of the multiplexers.

If the field code line appears on the top of each playback channel, decrease the value.

If multiplexers can not playback properly ,increase the value.

(5) DISK RENEW :

YES/NO : Activates the Renew HDD option.

DISK RENEW

 

NO

 

YES

Press NO to renew HDD and Press ENTER key to Exit.

 

 

 

 

 

 

 

 

 

 

Press Yes to Renew HDD and Press ENTER key to Exit.

 

DISK

RENEW

 

 

 

 

 

 

 

NO

 

YES

 

 

 

 

 

 

 

 

(6) SYSTEM UPDATE :

YES/NO : Updates the system.

YES : Copy the update files into Compact Flash card ON PC and insert the

Compact Flash card into the slot, and then press ENTER key to update system.

The “ Reading Program… … … ” will be shown on the screen during the process.

The “ Success” will be shown on the screen after system update.

Notice: After the system is updated successfully, be sure reboot the system.

29

Image 35
Contents EDSR100H Safety Precautions Safety Warning AC100V~240V Power Cords Important Safeguards Important SafeguardsTable of Contents Product Overview Product Overview and FeaturesSpecifications Left/Right Button Press Up/Down Button Press Front Panel KeypadsFront Panel Keypads Jog and Shuttle Dial Display Press this key to switch ON/OFFAudio PowerBack Panel Connections Back Panel ConnectionsVideo in /Output Alarm Input/ OutputMonitor RS232 One Camera Connection System ConnectionSystem Connection Multiplexer Main Monitor Output Multiplexer ConnectionMain Monitor Multiplexer VCR Out Multiplexer VCRQuad Main Monitor Out Quad Connection. Quad with VCR in VCR out connectorMain Monitor Quad VCR Out Quad VCRMain Monitor Quad Video Out to Video Recorder Quad connection. Quad without VCR in VCR out connectorInstallation Menu Menu Language English CLOCK/ Language Setting MenuVersion 1.0 2003/05/26 CLOCK/LANGUAGE Setting Menu , we SET Date 2003/04/24 TUE TimeEND on JAN 1ST MON Daylight Setting MenuFrom 0000 to Daylight Setting Menu , we define From 0000 toStandard OFF Timer Setting MenuTimer Setting Menu Week Start Stop Speed Quality SET SUN Standard OFF SUNSET SpeedNormal Recording MENU, we define Normal Record Setting MenuDisk Full MultiplexerRecording Quality Alarm Record Setting MenuAlarm Record Setting Menu Alarm Operation Recording Speed PRE-ALARM Operation Recording SpeedPRE Alarm Time Alarm Reset TypePRE-ALARM Operation 15Figure 1 Normally Closed Connection use pin # 13 and # Alarm outNormally open connection use pin # 13 and # Circuit AlarmAlarm in and alarm reset AlarmRecord Buzzer Setting MenuTime Stamp Archive Setting MenuArchive Setting Menu Picture Size 720x576Parity None Data BIT Stop BIT RS232/RS485 Setting MenuBaud Rate OFF System Setting MenuSystem Setting Menu Play with Audio Password Enable PasswordPress Yes to Renew HDD and Press Enter key to Exit Press no to renew HDD and Press Enter key to ExitCF Renew REC Stop RecordingInstant Recording Press Record key to start the recording immediatelyMenu Alarm RecordingPress Menu key and turn the jog dial to select the Alarm Recording Setting Menu Recording OperationREV.PLAY Playing BackNormal Playback PlayFrame/Field advance Forward/Reverse Slow Forward/Reverse PlaybackPause Search Search PlaybackSegment Search Playback Alarm Search Playback Date/Time Search Playback Press the Pause key to freeze the picture CopyStill Image Copy Press the Play key to start playing backCopy Copy to Movie File Copy to Movie FilePress Copy key and then the copy menu appears Pause Search Stop Pin assignment of the 9-pin D-SUB connector Interface SpecificationsSUB 9-pin connector specifications Transmission settingRemote Control Protocol Receiver ID Digital Video Recorder Page Remote Controller Remote ControllerAppendix-A APPENDIX- A/Time Lapse Mode Recording TimeWhen Recording with 160-GB HDD Lock APPENDIX-B/SECURITY Lock SettingAppendix-B Beijing Office Head OfficeUSA Office Japan Office