EverFocus EDSR100H instruction manual Alarm in and alarm reset, Circuit

Page 30
Normally Open
(N.O.)

MENU

(c) Alarm in and alarm reset

There is 1 alarm sensor in for 1 channel and 1 alarm reset in, the alarm input can be set to Normally Open or Normally Closed by user.

 

 

ALARM

 

 

CIRCUIT

SENSOR 1

 

 

8

2

1

15

 

9

ALARM RESET

 

 

Alarm in

There is one alarm input. Please connect the alarm input in the same sequence as the camera input BNC.

When alarm signal comes in, the Digital Video Recorder will do the following:

1.Display Alarm Message

2.Turn on the buzzer if the buzzer setting is on.

The ALARM in can be selected as normally open input or normally closed input:

: If the alarm input is selected as Normally Open input, then the

input is opened normally, and shorted to the ground means an alarm happens. Normally Close : If the alarm input is selected as Normally Close input, then the

(N.C.) input is shored to the ground normally, and opened input means an alarm happens.

24

Page 29 Page 31
Image 30
Page 29 Page 31
Contents EDSR100H Safety Precautions Safety Warning AC100V~240V Power Cords Important Safeguards Important SafeguardsTable of Contents Product Overview and Features Product OverviewSpecifications Front Panel Keypads Front Panel KeypadsLeft/Right Button Press Up/Down Button Press Display Press this key to switch ON/OFF Jog and Shuttle DialBack Panel Connections PowerBack Panel Connections AudioAlarm Input/ Output MonitorVideo in /Output RS232 System Connection System ConnectionOne Camera Connection Multiplexer VCR Multiplexer ConnectionMain Monitor Multiplexer VCR Out Multiplexer Main Monitor OutputQuad VCR Quad Connection. Quad with VCR in VCR out connectorMain Monitor Quad VCR Out Quad Main Monitor OutQuad connection. Quad without VCR in VCR out connector Main Monitor Quad Video Out to Video RecorderInstallation Menu Date 2003/04/24 TUE Time CLOCK/ Language Setting MenuVersion 1.0 2003/05/26 CLOCK/LANGUAGE Setting Menu , we SET Menu Language EnglishFrom 0000 to Daylight Setting MenuFrom 0000 to Daylight Setting Menu , we define END on JAN 1ST MONStandard OFF SUN Timer Setting MenuTimer Setting Menu Week Start Stop Speed Quality SET SUN Standard OFFSpeed SETNormal Record Setting Menu Normal Recording MENU, we defineMultiplexer Disk FullPRE-ALARM Operation Recording Speed Alarm Record Setting MenuAlarm Record Setting Menu Alarm Operation Recording Speed Recording QualityAlarm Reset Type PRE-ALARM OperationPRE Alarm Time 15Figure 1 Alarm out Normally open connection use pin # 13 and #Normally Closed Connection use pin # 13 and # Alarm AlarmAlarm in and alarm reset CircuitBuzzer Setting Menu Record720x576 Archive Setting MenuArchive Setting Menu Picture Size Time StampRS232/RS485 Setting Menu Baud RateParity None Data BIT Stop BIT Password System Setting MenuSystem Setting Menu Play with Audio Password Enable OFFPress no to renew HDD and Press Enter key to Exit Press Yes to Renew HDD and Press Enter key to ExitCF Renew Press Record key to start the recording immediately RecordingInstant Recording REC StopRecording Setting Menu Recording Operation Alarm RecordingPress Menu key and turn the jog dial to select the Alarm MenuPlay Playing BackNormal Playback REV.PLAYSlow Forward/Reverse Playback PauseFrame/Field advance Forward/Reverse Search Playback Segment Search PlaybackSearch Alarm Search Playback Date/Time Search Playback Press the Play key to start playing back CopyStill Image Copy Press the Pause key to freeze the pictureCopy to Movie File Press Copy key and then the copy menu appearsCopy Copy to Movie File Pause Search Stop Transmission setting Interface SpecificationsSUB 9-pin connector specifications Pin assignment of the 9-pin D-SUB connectorRemote Control Protocol Receiver ID Digital Video Recorder Page Remote Controller Remote ControllerAPPENDIX- A/Time Lapse Mode Recording Time Appendix-AWhen Recording with 160-GB HDD APPENDIX-B/SECURITY Lock Setting Appendix-BLock Japan Office Head OfficeUSA Office Beijing Office
Top Page Image Contents