Philips PHDVR8L owner manual Direct Code Entry Code Search, Code Search by Brand

Page 6

Direct Code Entry

Code Search, cont.

1.Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button.

2.Press and release the desired mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.

3.Enter the 4 digit code from the code tables (on separate sheet). Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.

4.With your device on, press CHANNELUP. If the device responds, no further programming is required. Note: If some buttons do not operate your equipment, try one of the other codes for your brand.

Write your codes down here for easy reference later.

Type

Type stored

Code

 

 

 

TV

 

 

VCR

 

 

DVD

 

 

CBL

 

 

SAT

 

 

CD

 

 

AUDIO

 

 

DVR

 

 

 

 

 

Code Search

If your product does not respond after you have tried all the codes for your brand, or if your brand is not listed, try searching for your code by following these steps.

1.Manually turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the CODE SEARCH button until the red indicator stays on, then release the CODE SEARCH button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

5.Press and release MUTE to install the code.

10

Most users will store VCR codes under the VCR button, Cable codes under CABLE, etc. If (for example) you want to store a VCR code under CABLE, first follow the procedure for Direct Code Entry (previous page) and press CABLE in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search (or Brand Search, below). Note: If the device does not have a CHANNEL UP button, use PLAY (VCR only) or POWER instead. Code Search starts from the currently stored 4 digit number under that mode.

Code Search by Brand

Lets you search for a code for a specific Brand within the Code Library for a particular manufacturer.

1.Turn on the device (TV, VCR, etc.) to be controlled.

2.Press and hold the CODE SEARCH button until the red indicator remains on, then release CODE SEARCH button.

3.Press and quickly release the desired mode button (TV, VCR, etc.). The red indicator blinks off once.

4.Press and release the numeric button (0-9) corresponding to desired Manufacturer (see table on code list sheet). The red indicator blinks off once. Note, pressing “0” performs a full library search same as normal Code Search Method on previous page.

5.Press the CHANNEL UP button ((or POWER or PLAY (VCR only)) repeatedly until the device to be controlled changes channel. The red indicator blinks off with each button press. If you accidentally overshoot the code required, press the CHANNEL DOWN button to backtrack through the library until the device changes channel. Pressing CHANNEL UP changes direction to forward again.

6.Press and release MUTE to install the code.

Brand Search Method entry is now complete.

Note: When all codes under a Brand have been searched the red indicator flashes rapidly for 3 seconds.

11

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PHDVR8L Table of Contents IntroductionVolume UP/DOWN Changes the volume level Button Functions Button Functions,Tivo/Replay Functions labeled in Green TiVo code is DVD Functions labeled in BlueSAT Functions Replay code isSetup Direct Code Entry Code Search, Code SearchCode Search by Brand Code Identification Feature Sleep Timer Setup, Programming Combo Device CodesSetting ALLVolume/Mute Control to any one Mode Code LearningIR Transmitter Finder Feature Tips On Learning,To Clear all Learned Commands under a mode Learning CommandsClearing Commands Master Clear To Clear all Learned Commands under all modesMacros, To Setup a MacroMacros Macro NotesTroubleshooting Limited Lifetime WarrantyÍndice IntroducciónFunciones de botones Funciones de DVD con leyendas en azul Replay el código esInstalación de baterías PreparaciónFunciones de audio con leyendas en rojo Ahorrador de bateríasPreparación, Ingreso Directo de CódigosProgramacíon con Búsqueda de codigos Función de Identificación de Códigos Cronometro de apagado automáticoCódigos de programación de equipos combinados Control de equipos combinadosPreparación, Transferencia de códigos Consejos Para el AprendizajeConsejos Para el Aprendizaje, Aprendizaje de Comandos Despejando Comandos Borrado de macros Programación de una macroCómo programar una macro Notas sobre las macrosEl Control Remoto no Opera su Producto El Control Remoto no Opera Algunas Funciones de su AparatoTable des matières Certaines touches de la télécommande peuvent avoir des Fonctions des touches Fonctions des touches,Fonctions TiVo/ReplayTV en vert TiVo code DVD Functions labeled in BlueFonctions SAT ReplayTV codeFonctions audio en rouge ConfigurationInstallation des piles Économiseur de pilesConfiguration suite Programmation au moyen de la fonction de recherche des codesFonction d’identification des codes Minuteur de mise en veilleContrôle des combinés Accès direct aux modes VCR/DVD/DVRConfiguration suite Apprentissage de codes Conseils Sur L’ApprentissageConseils Sur L’Apprentissage suite Commandes D’Enregistrement Suppression des commandesPour Effacer Toutes Les Commandes Enregistrees Sous Un Mode Pour enregistrer une macro Pour supprimer une macroDépannage Garantie a vie limitéeLe témoin clignote une fois le code programmé
Top Page Image Contents