dbx Pro 260 user manual Name Rock Venue, Saving Configuration Changes

Page 34

Section 3	Configuring the DriveRack™	DriveRack	™

NAME: Output Ch2

<DATA> - SELECT CHARACTER <PREV/NEXTPG> - LEFT/RIGHT <STORE>-EDIT/<UTIL>-EXIT

•Once all of the naming assignments have been made, press the UTILITY button to return to Configuration mode. If all Configuration modifications you can press the PROGRAM button to return to program mode where you will proceed to Store your new USER configuration.

3.6Saving Configuration Changes

Once changes have been made to the current Configuration, changes can be saved by pressing the STORE button and the display will appear like this:

NAME: ROCK VENUE

<DATA> - SELECTS CHARACTER <PREV/NEXTPG> - LEFT/RIGHT: PRESS <STORE> TO ADVANCE

At this point, enter the new name for your configuration. If you wish to abort at this point, press the PROGRAM/CONFIG button.

®

26	DriveRack™ User Manual

Image 34

Contents 260 Important Safety Instructions Electromagnetic Compatibility Table of Contents DriveRackIntro IntroductionDriveRack DriveRack featuresDefining the 260 DriveRack System Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Rear Panel Connections Getting StartedFront Panel Function Buttons LCD DisplayData Wheel Input MetersQuick Start Output MetersDriveRack System Setup StereoSub Speaker Auto EQ Wizard AFS WizardAFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Basic Navigation Modes Editing FunctionsEffect Button Array Overview Navigating the EQ -GEQ and PEQ Navigating the Xover SectionNavigating the Other Section Navigating the Dynamics SectionNavigating the Delay Section Navigating the Utility/Meters SectionNavigating the Wizard Section Navigating the I/O SectionFunctions Navigating Factory Programs Configuring the DriveRackProgram Definition Selecting ProgramsEditing Factory Programs Navigation ModesStore Program Replacing Saving Factory Programs ChangesSelect Creating a User ConfigurationSignal Path Link/UnlinkMono DLY 1.3 10 ms Unused Select Link/Unlink Select Link/UnlinkSelect Route Mono DLY 20 MS 810 ms Unused Select Link/Unlink Route Name Output Ch2Saving Configuration Changes Name Rock VenueDetailed Detailed Parameters Pre-Crossover EQFeedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Crossover Notch FiltersPost-CROSSOVER PEQ Compressor/Limiter Gain G -20 to +20 dB Threshold T -40 to +20dBuRatio R 1.0 to Inf1 Auto On/OffRelease 360 to 5 dB / Sec per band or global Attack .01 to 200 m Sec per band or globalHold 0 to 500 m Sec per band or global Peakstop+ On/OffAlignment Delay Input RoutingNoise Level -10 to 10 Mixer and Router Phase 0 toOutput Shift On/OffMeters Utilities/Meters Power Up Modes PUP Program Stored PUP Mute CurrentUtility LCD Contrast Auto EQ Plot 1 LCD Contrast / Auto EQ PlotZC Setup Panel None 3 ZC SetupPanel 1 ZC-3 Select a No Change Panel 1 ZC-4 Switch 1 2 3 No ChangePanel ZC-2 Boost 0dB Cut Output 4 -6 SecuritySet Security Level Pre EQ Low Set 260 Device Level HighPassword Edit High Password Edit Med Password Password Enter PasswordProgram List List Size List Index Prog Change Mode Program List Prog Lock7-8 Program List/Program Change Output Jumpers Setting 8 Output Jumper SwitchesZone Controllers Panel Insa Comp o+LIM 0+ MetersOutput Trims Net Remote Control Remote Control PC GUI InstallationSection GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Zone Controller Wiring Diagram a Diagram BDriveRack DriveWare Functions Page Guide Hardware Application GuideMono Four-Way w/ Two Aux Zones SoftwareDriveRack Stereo Tri-ampStereo with Four Aux Zones Stereo Bi-amp w/ Dual Delay DriveRackDriveRack DriveRackAppendix Factory Reset Power Up Quick Key OptionsSpecifications Appendix aAuto EQ Optimization Tips Look out for ModesCrossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams System Setup and Gain Structure Gain Level JumpersDriveRack Harman International Company