dbx Pro 260 user manual DriveRack, Stereo Tri-amp

Page 69

DriveRack™	Application Guide	Section 7

	7.2- Stereo Tri-amp

Hardware

1.Connect the outputs from the mixer to the inputs of the DriveRack™.

2.Connect the outputs of the DriveRack™ and run to the selected speaker amplifier.

3.Making sure that all outputs are muted, apply power to the mixer and amplifiers.

Software

1.Select a program (Factory: 2x6 Stereo) as a template.

2.Load the program by pressing the PROG/CONFIG button.

3.Adjust the individual parameters for the system by pressing the Processing Module buttons

Left

Right

2

3

4

5

MA-5002VZ

JBL SR4731X

JBL 4719X

®

DriveRack™ User Manual	61

Image 69

Contents 260 Important Safety Instructions Electromagnetic Compatibility DriveRack Table of ContentsIntro DriveRack features IntroductionDriveRackDefining the 260 DriveRack System DriveRackIntroduction Service Contact InfoIntroductionDriveRack Warranty Section Getting Started Rear Panel ConnectionsFront Panel Data Wheel LCD DisplayFunction Buttons Input MetersOutput Meters Quick StartDriveRack Stereo System SetupSub Speaker AFS Wizard Auto EQ WizardAFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Editing Functions Basic Navigation ModesEffect Button Array Overview Navigating the Xover Section Navigating the EQ -GEQ and PEQNavigating the Dynamics Section Navigating the Other SectionNavigating the Utility/Meters Section Navigating the Delay SectionNavigating the I/O Section Navigating the Wizard SectionFunctions Program Definition Configuring the DriveRackNavigating Factory Programs Selecting ProgramsNavigation Modes Editing Factory ProgramsSaving Factory Programs Changes Store Program ReplacingSignal Path Creating a User ConfigurationSelect Link/UnlinkSelect Link/Unlink Mono DLY 1.3 10 ms Unused Select Link/UnlinkSelect Route Route Name Output Ch2 Mono DLY 20 MS 810 ms Unused Select Link/UnlinkName Rock Venue Saving Configuration ChangesDetailed Pre-Crossover EQ Detailed ParametersFeedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Notch Filters CrossoverPost-CROSSOVER PEQ Compressor/Limiter Ratio R 1.0 to Inf1 Threshold T -40 to +20dBuGain G -20 to +20 dB Auto On/OffHold 0 to 500 m Sec per band or global Attack .01 to 200 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Peakstop+ On/OffInput Routing Alignment DelayOutput Phase 0 toNoise Level -10 to 10 Mixer and Router Shift On/OffMeters Utility LCD Contrast Auto EQ Plot Power Up Modes PUP Program Stored PUP Mute CurrentUtilities/Meters 1 LCD Contrast / Auto EQ Plot3 ZC Setup ZC Setup Panel NonePanel ZC-2 Boost 0dB Cut Output Panel 1 ZC-4 Switch 1 2 3 No ChangePanel 1 ZC-3 Select a No Change 4 -6 SecuritySet 260 Device Level High Set Security Level Pre EQ LowPassword Enter Password Password Edit High Password Edit Med PasswordProg Change Mode Program List Prog Lock Program List List Size List Index7-8 Program List/Program Change 8 Output Jumper Switches Output Jumpers SettingLIM 0+ Insa Comp o+Zone Controllers Panel MetersOutput Trims Net Remote Control PC GUI Installation Remote ControlSection GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Diagram a Diagram B Zone Controller WiringDriveRack DriveWare Functions Page Guide Mono Four-Way w/ Two Aux Zones Application GuideHardware SoftwareStereo Tri-amp DriveRackStereo with Four Aux Zones DriveRack Stereo Bi-amp w/ Dual DelayDriveRack DriveRackAppendix Power Up Quick Key Options Factory ResetAppendix a SpecificationsLook out for Modes Auto EQ Optimization TipsCrossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams Gain Level Jumpers System Setup and Gain StructureDriveRack Harman International Company