dbx Pro 260 Utility LCD Contrast Auto EQ Plot, Power Up Modes PUP Program Stored PUP Mute Current

Page 48

Section 5

Utilities/Meters

DriveRack

™

 

 

 

 

The Utility section of the 260 DriveRack gives you the ability to perform several key operational functions to the DriveRack including: Security settings, Power-up features, Program list organi- zation, Auto EQ plotting, adjustment of Output Jumper settings and Display contrast settings. Additionally, pressing and holding the utility button will allow you to enter the metering sec- tion of the 260. This section lets you monitor aspects of the unit including: Compression, Limiting, Zone Controller levels and Output trim. Use this section of the manual to make your- self familiar with all aspects of the Utility menu of the DriveRack system.

5.1.1 -Page 1 - LCD Contrast / Auto EQ Plot

Page 1 of the Utility menu offers LCD contrast control and Auto EQ Plot selection. Since venues and applications vary, the 260 DriveRack provide you with the option of changing the contrast of the custom display. To make any adjustments to the display contrast, press the UTILITY button and the page will appear as follows:

Utility

 

LCD Contrast

10

Auto EQ Plot

RTA

 

 

•Select the Contrast adjustment by pressing the DATA wheel until the con- trast percentage is selected. Once the contrast has been selected, proceed to rotate the DATA wheel until the desired contrast has been established. Contrast adjust ranges from 01 to 16.

•Select the RTA or GEQ for the Auto EQ plot press the DATA wheel until the Auto EQ Plot is selected. Once the desired option has been selected, pro- ceed to rotate the DATA wheel select either RTA or GEQ. To exit, press the PROGRAM/CONFIG button.

5.1.2-Page 2 - PUP Program/Mute

The Utility menu of the 260 DriveRack also offers the option of setting the PUP (Power Up) Program option of either Current or Stored and PUP Mutes, which allows to you power up with all outputs either muted or at the last setting prior to powering down. The following explains the difference between Load On and Load OFF settings. To access and edit the Load Stored option of the unit, use the following procedure.

•From Program mode, press the UTILITY button and use the PREV PG and NEXT PG but- ton to move to the page that appears as follows:

Power Up Modes

 

PUP Program

Stored

PUP Mute

Current

 

 

Stored: After cycling the power (or power failure), the unit will automatically load a program from the program table. No unstored edits will be saved.

®

40

DriveRack™ User Manual

 

 

Page 47 Page 49
Image 48
Page 47 Page 49
Contents 260 Important Safety Instructions Electromagnetic Compatibility Table of Contents DriveRackIntro DriveRack features IntroductionDriveRackDefining the 260 DriveRack System Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Getting Started Rear Panel ConnectionsFront Panel LCD Display Data WheelFunction Buttons Input MetersQuick Start Output MetersDriveRack System Setup StereoSub Speaker Auto EQ Wizard AFS WizardAFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Editing Functions Basic Navigation ModesEffect Button Array Overview Navigating the EQ -GEQ and PEQ Navigating the Xover SectionNavigating the Other Section Navigating the Dynamics SectionNavigating the Delay Section Navigating the Utility/Meters SectionNavigating the Wizard Section Navigating the I/O SectionFunctions Configuring the DriveRack Program DefinitionNavigating Factory Programs Selecting ProgramsEditing Factory Programs Navigation ModesStore Program Replacing Saving Factory Programs ChangesCreating a User Configuration Signal PathSelect Link/UnlinkSelect Link/Unlink Mono DLY 1.3 10 ms Unused Select Link/UnlinkSelect Route Mono DLY 20 MS 810 ms Unused Select Link/Unlink Route Name Output Ch2Saving Configuration Changes Name Rock VenueDetailed Detailed Parameters Pre-Crossover EQFeedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Notch Filters CrossoverPost-CROSSOVER PEQ Compressor/Limiter Threshold T -40 to +20dBu Ratio R 1.0 to Inf1Gain G -20 to +20 dB Auto On/OffAttack .01 to 200 m Sec per band or global Hold 0 to 500 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Peakstop+ On/OffAlignment Delay Input RoutingPhase 0 to OutputNoise Level -10 to 10 Mixer and Router Shift On/OffMeters Power Up Modes PUP Program Stored PUP Mute Current Utility LCD Contrast Auto EQ PlotUtilities/Meters 1 LCD Contrast / Auto EQ PlotZC Setup Panel None 3 ZC SetupPanel 1 ZC-4 Switch 1 2 3 No Change Panel ZC-2 Boost 0dB Cut OutputPanel 1 ZC-3 Select a No Change 4 -6 SecuritySet Security Level Pre EQ Low Set 260 Device Level HighPassword Edit High Password Edit Med Password Password Enter PasswordProg Change Mode Program List Prog Lock Program List List Size List Index7-8 Program List/Program Change Output Jumpers Setting 8 Output Jumper SwitchesInsa Comp o+ LIM 0+Zone Controllers Panel MetersOutput Trims Net Remote Control Remote Control PC GUI InstallationSection GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Zone Controller Wiring Diagram a Diagram BDriveRack DriveWare Functions Page Guide Application Guide Mono Four-Way w/ Two Aux ZonesHardware SoftwareDriveRack Stereo Tri-ampStereo with Four Aux Zones Stereo Bi-amp w/ Dual Delay DriveRackDriveRack DriveRackAppendix Factory Reset Power Up Quick Key OptionsSpecifications Appendix aAuto EQ Optimization Tips Look out for ModesCrossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams System Setup and Gain Structure Gain Level JumpersDriveRack Harman International Company
Top Page Image Contents