dbx Pro 260 user manual DriveRack, Table of Contents

Page 4

	DriveRack™				Table of Contents
Introduction			4.8	Post-Crossover PEQ		33
0.1	Defining the 260 DriveRack	ii	4.9	Compressor/Limiter		34
0.2	Service Contact Info	iii	4.10		Alignment Delay	37
0.3	Warranty	iv	4.11		Input Routing	37
			4.12		Output	38

Section 1 - Getting Started

1.1	Rear Panel Connections	2
1.2	Front Panel	2
1.3	Quick Start	4
Section 2 - Editing Functions
2.1	Basic Navigation Modes	14
2.2	Effect Button Array Overview	14
2.3	Navigating the Pre-EQ Section	15
2.4	Navigating the Crossover Section	15
2.5	Navigating the Other Section	16
2.6	Navigating the Dynamics Section	16
2.7	Navigating the Delay Section	17
2.8	Navigating the Utility/Meters Section	17
2.9	Navigating the Wizard Section	18
2.10 Navigating the I/O Section		18

Section 5 - Utilities/Meters
5.1.1 LCD Contrast/Auto EQ Plot	40
5.1.2 PUP Program/Mute	40
5.1.3 ZC Setup	41
5.1.4 Security	42
5.1.5 Program List/Program change	45
5.1.6 Output Jumper switches	46
5.2.1 Meters	47
Section 6 - Remote Control
6.1.1 PC GUI Installation	50
System Requirements	50
Install	50
Basic Operation	50
Cable specs	52
6.2.1 ZC-Zone Controllers	53

Section 3 - Configuration Functions

3.1	Program Definition	20
3.2	Navigating Factory Programs	20
3.3	Editing Factory Programs	21
3.4	Saving Factory Program Changes	22
3.5	Creating a User Configuration	23
3.6	Saving Configuration Changes	26
Section 4 - Detailed Parameters
4.1	Pre-Crossover EQ (31 Band Graphic) or
	(9-Band Parametric)	28
4.2	Feedback Eliminator (AFS)	29
4.3	Subharmonic Synthesizer	30
4.4	Noise Gate	31
4.5	Automatic Gain Control (AGC)	32
4.6	Notch Filters	33
4.7	Crossover	33

Section 7 - Application Guide

7.1	Mono 4-Way w/ 2 Aux Zones		58
7.2	Stereo Tri-Amp		59
7.3	Stereo w/ 4 Aux Zones		60
7.4	Stereo Bi-Amp w/ Dual Delays		61
Appendix
A.1		Factory Reset	64
A.2		Power up Quick Key Options	64
A.3		Specifications	65
A.4		Auto EQ Optimization	66
A.5		Crossover Diagrams	67
A.6		Prog List/Speaker Tunings/
		Power Amp Tunings	68
A.7		Block Diagram	69
A.8		Input and Output Section Diagrams	70
A.9		Gain Level Jumpers	71
A.10 System Setup and Gain Structure			71

®

Table of Contents DriveRack™ User Manual

Image 4

Contents 260 Important Safety Instructions Electromagnetic Compatibility Table of Contents DriveRackIntro IntroductionDriveRack DriveRack featuresDefining the 260 DriveRack System Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Rear Panel Connections Getting StartedFront Panel LCD Display Data WheelFunction Buttons Input MetersQuick Start Output MetersDriveRack System Setup StereoSub Speaker Auto EQ Wizard AFS WizardAFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Basic Navigation Modes Editing FunctionsEffect Button Array Overview Navigating the EQ -GEQ and PEQ Navigating the Xover SectionNavigating the Other Section Navigating the Dynamics SectionNavigating the Delay Section Navigating the Utility/Meters SectionNavigating the Wizard Section Navigating the I/O SectionFunctions Configuring the DriveRack Program DefinitionNavigating Factory Programs Selecting ProgramsEditing Factory Programs Navigation ModesStore Program Replacing Saving Factory Programs ChangesCreating a User Configuration Signal PathSelect Link/UnlinkMono DLY 1.3 10 ms Unused Select Link/Unlink Select Link/UnlinkSelect Route Mono DLY 20 MS 810 ms Unused Select Link/Unlink Route Name Output Ch2Saving Configuration Changes Name Rock VenueDetailed Detailed Parameters Pre-Crossover EQFeedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Crossover Notch FiltersPost-CROSSOVER PEQ Compressor/Limiter Threshold T -40 to +20dBu Ratio R 1.0 to Inf1Gain G -20 to +20 dB Auto On/OffAttack .01 to 200 m Sec per band or global Hold 0 to 500 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Peakstop+ On/OffAlignment Delay Input RoutingPhase 0 to OutputNoise Level -10 to 10 Mixer and Router Shift On/OffMeters Power Up Modes PUP Program Stored PUP Mute Current Utility LCD Contrast Auto EQ PlotUtilities/Meters 1 LCD Contrast / Auto EQ PlotZC Setup Panel None 3 ZC SetupPanel 1 ZC-4 Switch 1 2 3 No Change Panel ZC-2 Boost 0dB Cut OutputPanel 1 ZC-3 Select a No Change 4 -6 SecuritySet Security Level Pre EQ Low Set 260 Device Level HighPassword Edit High Password Edit Med Password Password Enter PasswordProgram List List Size List Index Prog Change Mode Program List Prog Lock7-8 Program List/Program Change Output Jumpers Setting 8 Output Jumper SwitchesInsa Comp o+ LIM 0+Zone Controllers Panel MetersOutput Trims Net Remote Control Remote Control PC GUI InstallationSection GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Zone Controller Wiring Diagram a Diagram BDriveRack DriveWare Functions Page Guide Application Guide Mono Four-Way w/ Two Aux ZonesHardware SoftwareDriveRack Stereo Tri-ampStereo with Four Aux Zones Stereo Bi-amp w/ Dual Delay DriveRackDriveRack DriveRackAppendix Factory Reset Power Up Quick Key OptionsSpecifications Appendix aAuto EQ Optimization Tips Look out for ModesCrossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams System Setup and Gain Structure Gain Level JumpersDriveRack Harman International Company