dbx Pro 260 user manual Crossover Diagrams

Page 77

DriveRack™			Appendix A
			A.5 Crossover Diagrams
1X1(1-band)	1X2(2-band)	1X3(3-band)	1X4(4-band)
BP	H	H	H
BP	BP	BP	BP
BP
	L	M	MH
	BP	BP	BP
		L	ML
	1X6(4-band)	BP	BP
1X5(4-band)	1X6(4-band)
1X5(4-band)	H		L
	BP		L
	BP		BP
H			BP
H
BP	MH
	MH
MH	BP	2X2	2X3(2-band)
MH		2X2
BP
BP

		ML
		BP			L		LH
ML				L			LH
ML				L	L
BP					L
BP
		L		BP		BP
		BP		BP

					R		RH
L				R	R
L					R
BP
BP
		L
		BP
L
BP		L			+	BP	L Mono
		L			+
		BP
2X4(2-band)			2X5 (3-band)		2X6 (3-band)
	LH			LH			LH
L		L		LH			LH
L					L
					L
BP				BP		BP
R	RH			RH			RH
		R		RH	R		RH


	LL			LM			LM
				LM			LM
BP	RL			BP		BP
	RL			RM			RM
				RM			RM
			+	L Mono			LL
			+	L Mono
				BP
						BP
							RL

®

DriveRack™ User Manual	69

Image 77

Contents 260 Important Safety Instructions Electromagnetic Compatibility DriveRack Table of ContentsIntro Defining the 260 DriveRack System DriveRack featuresIntroductionDriveRack DriveRackIntroduction Service Contact InfoIntroductionDriveRack Warranty Section Front Panel Getting StartedRear Panel Connections Data Wheel LCD DisplayFunction Buttons Input MetersOutput Meters Quick StartDriveRack Stereo System SetupSub Speaker AFS Wizard Auto EQ WizardAFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Effect Button Array Overview Editing FunctionsBasic Navigation Modes Navigating the Xover Section Navigating the EQ -GEQ and PEQNavigating the Dynamics Section Navigating the Other SectionNavigating the Utility/Meters Section Navigating the Delay SectionNavigating the I/O Section Navigating the Wizard SectionFunctions Program Definition Configuring the DriveRackNavigating Factory Programs Selecting ProgramsNavigation Modes Editing Factory ProgramsSaving Factory Programs Changes Store Program ReplacingSignal Path Creating a User ConfigurationSelect Link/UnlinkSelect Route Select Link/UnlinkMono DLY 1.3 10 ms Unused Select Link/Unlink Route Name Output Ch2 Mono DLY 20 MS 810 ms Unused Select Link/UnlinkName Rock Venue Saving Configuration ChangesDetailed Pre-Crossover EQ Detailed ParametersFeedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Post-CROSSOVER PEQ Notch FiltersCrossover Compressor/Limiter Ratio R 1.0 to Inf1 Threshold T -40 to +20dBuGain G -20 to +20 dB Auto On/OffHold 0 to 500 m Sec per band or global Attack .01 to 200 m Sec per band or globalRelease 360 to 5 dB / Sec per band or global Peakstop+ On/OffInput Routing Alignment DelayOutput Phase 0 toNoise Level -10 to 10 Mixer and Router Shift On/OffMeters Utility LCD Contrast Auto EQ Plot Power Up Modes PUP Program Stored PUP Mute CurrentUtilities/Meters 1 LCD Contrast / Auto EQ Plot3 ZC Setup ZC Setup Panel NonePanel ZC-2 Boost 0dB Cut Output Panel 1 ZC-4 Switch 1 2 3 No ChangePanel 1 ZC-3 Select a No Change 4 -6 SecuritySet 260 Device Level High Set Security Level Pre EQ LowPassword Enter Password Password Edit High Password Edit Med Password7-8 Program List/Program Change Prog Change Mode Program List Prog LockProgram List List Size List Index 8 Output Jumper Switches Output Jumpers SettingLIM 0+ Insa Comp o+Zone Controllers Panel MetersOutput Trims Net Remote Control PC GUI Installation Remote ControlSection GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Diagram a Diagram B Zone Controller WiringDriveRack DriveWare Functions Page Guide Mono Four-Way w/ Two Aux Zones Application GuideHardware SoftwareStereo Tri-amp DriveRackStereo with Four Aux Zones DriveRack Stereo Bi-amp w/ Dual DelayDriveRack DriveRackAppendix Power Up Quick Key Options Factory ResetAppendix a SpecificationsLook out for Modes Auto EQ Optimization TipsCrossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams Gain Level Jumpers System Setup and Gain StructureDriveRack Harman International Company