dbx Pro Complete dbx Driverack PA Factory Reset and Unlock Instructions
Page 74

Appendix A

DriveRack™

A.1 Factory Reset

In the event that a reset is required, the DriveRack™ 260 offers you the option of performing a “Soft” or “Hard” reset. The Soft Reset resets all operating parameters except user programs. The Hard Reset Procedure will reset all program- mable information back to the factory defaults.

All Power-Up Functions require a button(s) to be pressed and held as the unit power is turned on. DriveRack 260 Power-Up Button Functions

Factory (“Hard”) Reset.

Press and hold the <STORE> button at power-up until the following message appears:

“! HARD RESET?”

“Yes <PREV PAGE>”

“No <PROGRAM>”

•Pressing the <PREV PAGE> button will start a Factory Reset (All User Programs will become copies of the Factory Programs, all Utility settings will be defaulted, and all Security settings will be defaulted).

•Pressing the <PROGRAM> button will abort the Factory Reset sequence and the unit will reset normally.

System (“SOFT”) Reset

• Press and hold the <UTILITY> button at power-up until the following message appears:

“! SOFT RESET?”

“Yes <PREV PAGE>”

“No <PROGRAM>”

•Pressing the <PREV PAGE> button will start a System Reset (All Utility settings will be defaulted.)

•Pressing the <PROGRAM> button will abort the System Reset sequence and the unit will reset normally.

A.2 Power Up Quick Key Options

The DriveRack™ 260 offer several “Quick Key” options for initial power up and are as follow:

Change Initial Program Number

•To change the initial power program number, Press and hold the <PROGRAM> button at power-up until the following message appears:

Use Wheel to”Change Restart”Program Number”

•Turning the <DATA> wheel will select the program you wish to load at initial reset.

•Press the <PROGRAM> button again when the selection is complete. Normal resetting will continue.

System Lock Out

• Press and hold <RTA> at power-up until one of the following messages appears:

System Unlocked All user input will be accepted or

System Locked No user input will be accepted

•Rotating the <DATA> wheel to select either Lock, Unlock or Filter Unlocked the system.

•Pressing <PREV PAGE> will unlock the system if it were locked or it will lock the system if it were unlocked.

•If you wish to leave the system locked with the exception of being able to clear the feedback filters, follow the same procedure on power up and then rotate the <DATA> wheel to select the feedback filter unlock feature.

•Pressing any other button will abort the System Lockout sequence and the unit will reset normally.

®

66

DriveRack™ User Manual

 

 

Page 73 Page 75
Image 74
Page 73 Page 75
Contents 260 Important Safety Instructions Electromagnetic Compatibility Table of Contents DriveRackIntro Defining the 260 DriveRack System DriveRack featuresIntroductionDriveRack Service Contact Info DriveRackIntroductionIntroductionDriveRack Warranty Section Front Panel Getting StartedRear Panel Connections Function Buttons LCD DisplayData Wheel Input MetersQuick Start Output MetersDriveRack System Setup StereoSub Speaker Auto EQ Wizard AFS WizardAFS Select total number of AFS filters Slowly Increase Mixer gain to Desired level DriveRack Section Effect Button Array Overview Editing FunctionsBasic Navigation Modes Navigating the EQ -GEQ and PEQ Navigating the Xover SectionNavigating the Other Section Navigating the Dynamics SectionNavigating the Delay Section Navigating the Utility/Meters SectionNavigating the Wizard Section Navigating the I/O SectionFunctions Navigating Factory Programs Configuring the DriveRackProgram Definition Selecting ProgramsEditing Factory Programs Navigation ModesStore Program Replacing Saving Factory Programs ChangesSelect Creating a User ConfigurationSignal Path Link/UnlinkSelect Route Select Link/UnlinkMono DLY 1.3 10 ms Unused Select Link/Unlink Mono DLY 20 MS 810 ms Unused Select Link/Unlink Route Name Output Ch2Saving Configuration Changes Name Rock VenueDetailed Detailed Parameters Pre-Crossover EQFeedback Eliminator Subharmonic Synthesizer Gate Automatic Gain Control AGC Post-CROSSOVER PEQ Notch FiltersCrossover Compressor/Limiter Gain G -20 to +20 dB Threshold T -40 to +20dBuRatio R 1.0 to Inf1 Auto On/OffRelease 360 to 5 dB / Sec per band or global Attack .01 to 200 m Sec per band or globalHold 0 to 500 m Sec per band or global Peakstop+ On/OffAlignment Delay Input RoutingNoise Level -10 to 10 Mixer and Router Phase 0 toOutput Shift On/OffMeters Utilities/Meters Power Up Modes PUP Program Stored PUP Mute CurrentUtility LCD Contrast Auto EQ Plot 1 LCD Contrast / Auto EQ PlotZC Setup Panel None 3 ZC SetupPanel 1 ZC-3 Select a No Change Panel 1 ZC-4 Switch 1 2 3 No ChangePanel ZC-2 Boost 0dB Cut Output 4 -6 SecuritySet Security Level Pre EQ Low Set 260 Device Level HighPassword Edit High Password Edit Med Password Password Enter Password7-8 Program List/Program Change Prog Change Mode Program List Prog LockProgram List List Size List Index Output Jumpers Setting 8 Output Jumper SwitchesZone Controllers Panel Insa Comp o+LIM 0+ MetersOutput Trims Net Remote Control Remote Control PC GUI InstallationSection GUI Recommended Cable Specifications ZC-Zone Controllers DriveRack Zone Controller Wiring Diagram a Diagram BDriveRack DriveWare Functions Page Guide Hardware Application GuideMono Four-Way w/ Two Aux Zones SoftwareDriveRack Stereo Tri-ampStereo with Four Aux Zones Stereo Bi-amp w/ Dual Delay DriveRackDriveRack DriveRackAppendix Factory Reset Power Up Quick Key OptionsSpecifications Appendix aAuto EQ Optimization Tips Look out for ModesCrossover Diagrams Program List/ Speaker Tunings/ Power Amp Tunings Block Diagram Input and Output Diagrams System Setup and Gain Structure Gain Level JumpersDriveRack Harman International Company
Top Page Image Contents