Philips VRKD11YL, VRKD12BL warranty Turning on Your VCR

Page 11

●Before turning on your VCR, make sure there are batteries in the remote control and the VCR and TV are connected (see pages five and seven-10).

●You can not set up channels if you are using a Cable Box/DBS.

●The instructions on this page only work when you turn on the VCR for the first time. If there is a power failure or if the VCR is unplugged for more than one minute, you may need to repeat the instructions on this page.

1

Press the POWER button. The POWER light and the VCR/TV light will appear on the front of the VCR.

2

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The display shown below will appear on the TV.

LANGUAGE SELECT

B ENGLISH

[ON]

ESPAÑOL

3

Press the PLAY button or the STOP button to select ENGLISH or ESPAÑOL. [ON] will appear beside your choice.

4

Press the F.FWD button or the MENU button. AUTO SET UP will appear on the screen.

AUTO SET UP

5

Press the MENU button, the F.FWD button, or the REW(ind) button to begin automatic channel setup. AUTO SET UP will flash on the screen and channel numbers will appear in the top right corner of the screen. When channels are set up, the TV will go to the lowest channel available.

The VCR will memorize all available channels, so when you use the CHANNEL o/p button, you’ll only scan through channels that you receive.

Turning on Your VCR 11

2Turn on the TV. Set it to channel 3 or 4.

1

POWER

CHANNEL

 

PAUSE

PLAY

3

STOP

F. FWD4

5 REW

RECORD VCR/TV

SPEED MENU DISPLAY

EXIT/ C. RESET COUNTER MEMORY

Helpful Hints

•If you do not see any messages when you turn on the VCR, check your hookups, then try again. If you still do not see any messages, follow the steps under “Automatic TV Channel Setup” on page 12 and “Choosing a Language” on page 16.

•If you try to set up channels when there is no antenna or cable connect- ed to the VCR, channel setup will appear to take place. Eventually, AUTO SET UP will appear on the screen steadily, and channel setup will stop. Connect an antenna or cable to the ANT(enna) IN jack of the VCR, then press the MENU but- ton, the F.FWD button, or the REW(ind) button again. Channel setup will begin again.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Instruction Book Model No Serial No Dear Philips product ownerFor Customer Use This bolt of lightning indi- cates uninsulated materialDeclaration of Conformity FeaturesSafety Precautions IntroductionTable of Contents Erasure Prevention Putting Batteries in the Remote ControlUsing the Remote Control Holder VCR maintenanceSetting the Time and the Alarm Using the Alarm ClockPutting Batteries in the Alarm Clock Using the Alarm Clock HolderDisconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemRecording/Viewing Any Channel Cable SignalConnections Cable SignalRecording One Channel/Watching Another Cable Box/DBSHookups With a Stereo TV Turning on Your VCR Press the Menu button until the main menu appears Automatic TV Channel SetupAdding/Deleting Channels Automatic TV Channel Setup cont’dSetting the VCR Clock Your selection will flash on the screen in the AM/PM space Setting the VCR Clock cont’dChoosing a Language Press the EXIT/C. Reset button when you are finishedOn-Screen Displays OFF mode Press the Display button once Count modePress the Display button once Clock mode Record Button Remote Control ButtonsPower Button Remote Control Buttons cont’d VCR/TV Light Alarm ClockPower Light Timer LightFront Panel Video OUT Jack AC Power CordBack Panel Audio OUT JackRead and follow the steps below to play a tape PlayingVHS Quasi Play Back Sqpb 1Turn on the TV Insert a tape RecordingStopping an OTR Starting an OTRDetails are on page five Timer RecordingEnter the recording’s start time Repeat the procedure in to set the recording’s end timeTimer Recording cont’d Main menu will appear Cancelling a Timer RecordingCorrecting a Timer Recording To stop recording, press the Stop button VCR/TV light will disappearAntenna Rerecording Copying TapesSelect Auto Repeat Repeat PlayPress the Play button or the Stop button repeatedly to Super High Speed Searching LP/SLP Forward and Reverse Searching/Pausing a PicturePausing a Picture Forward and Reverse Searching SP/LP/SLPPicture Select Press the Play button to watch the tape Real-Time Counter MemoryAutomatic Playback Features Helpful Hints Helpful Hints cont’d Renewed Dictionary Dictionary/SpecificationsSpecifications Index Supplied Accessories
Top Page Image Contents