Philips VRKD12BL, VRKD11YL warranty Correcting a Timer Recording

Page 30

30 Timer Recording (cont’d)

Correcting a Timer Recording

If you need to correct a timer recording after you have finished setting the program, follow these steps. Make sure the VCR is on and is in VCR position. (The VCR/TV light will appear. If it does not, press the VCR/TV button once.)

1

Press the MENU button so that the details of your pro- grams appear on the screen. If there are no recordings set,

the main menu will appear.

	TIMER PROGRAMMING
	DATE	STA/END	CH
B1 05/04		07:30 PM	16
	FRI	08:30 PM	SP
3	05/11	10:00 PM	125
	W FRI	10:54 PM	SLP
5	05/21	11:00 PM	40
	DAILY	11:30 PM	SLP

2

Press the PLAY button or the STOP button to select the timer recording you want to correct.

3

Press the F.FWD button.

ONE TIME PROGRAM

PROGRAM NUMBER			1
PROGRAM NUMBER			1
DATE	05/04		FRI
START TIME 07:30			PM
END TIME 08:30			PM
CHANNEL	16
REC SPEED	SP

4

Select the information you want to change using the F.FWD button. Press the REW(ind) button to go back one step. (There is an exception. Do not press the REW(ind) button while the program number is flashing. If you do, you will cancel the timer recording completely.)

5

While the information is flashing, enter the correct infor- mation by pressing the PLAY button or the STOP button.

6

4

1

6

2&5

POWER

CHANNEL

PAUSE

PLAY

STOP

F. FWD3

REW

RECORD	VCR/TV
SPEED MENU DISPLAY
EXIT/ C. RESET	COUNTER MEMORY

When all the information is correct, press the EXIT/C.RESET button. Turn off the VCR before the timer recording.

Image 30

Contents Instruction Book This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial NoIntroduction FeaturesSafety Precautions Declaration of ConformityTable of Contents VCR maintenance Putting Batteries in the Remote ControlUsing the Remote Control Holder Erasure PreventionUsing the Alarm Clock Holder Using the Alarm ClockPutting Batteries in the Alarm Clock Setting the Time and the AlarmHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCable Signal ConnectionsRecording/Viewing Any Channel Cable Box/DBS SignalRecording One Channel/Watching Another CableHookups With a Stereo TV Turning on Your VCR Automatic TV Channel Setup Press the Menu button until the main menu appearsAutomatic TV Channel Setup cont’d Adding/Deleting ChannelsSetting the VCR Clock Setting the VCR Clock cont’d Your selection will flash on the screen in the AM/PM spacePress the EXIT/C. Reset button when you are finished Choosing a LanguageOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Displays Remote Control Buttons Power ButtonRecord Button Remote Control Buttons cont’d Timer Light Alarm ClockPower Light VCR/TV LightFront Panel Audio OUT Jack AC Power CordBack Panel Video OUT JackPlaying VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording 1Turn on the TV Insert a tapeStarting an OTR Stopping an OTRTimer Recording Details are on page fiveRepeat the procedure in to set the recording’s end time Enter the recording’s start timeTimer Recording cont’d Cancelling a Timer Recording Main menu will appearCorrecting a Timer Recording VCR/TV light will disappear To stop recording, press the Stop buttonRerecording Copying Tapes AntennaRepeat Play Press the Play button or the Stop button repeatedly toSelect Auto Repeat Forward and Reverse Searching SP/LP/SLP Forward and Reverse Searching/Pausing a PicturePausing a Picture Super High Speed Searching LP/SLPPicture Select Real-Time Counter Memory Press the Play button to watch the tapeAutomatic Playback Features Helpful Hints Helpful Hints cont’d Renewed Dictionary/Specifications SpecificationsDictionary Index Supplied Accessories