Philips VRKD12BL, VRKD11YL Real-Time Counter Memory, Press the Play button to watch the tape

Page 36

36 Real-Time Counter Memory

Follow the steps below to reset the real-time counter to zero at a tape location you want to refer to later. Make sure:

●The VCR is on and is in VCR position. The VCR/TV light will appear. If it does not, press the VCR/TV button once.

●There is a tape in the VCR.

	1
	Play, fast forward, or rewind a tape to the location that you would
	like to refer to later. Press the STOP button to stop the
	tape.
	2	1
	Press the EXIT/C.RESET button repeatedly to reset the	1
	Press the EXIT/C.RESET button repeatedly to reset the
	real-time counter to zero.

0 : 00 : 00

3

Within five seconds, press the COUNTER MEMORY but-

ton so that M appears on the screen beside the real-time 2 counter.

M 0 : 00 : 00

POWER

CHANNEL

PAUSE

PLAY

STOP

F.FWD

REW

RECORD VCR/TV

SPEED MENU DISPLAY

EXIT/ C. RESET COUNTER MEMORY

4

3

4

To go to a tape location where the real-time counter was reset to zero, press the REW(ind) button or the F.FWD button when playback is stopped.

When the tape reaches the point at which the real-time counter was reset to zero, the tape will stop.

Press the PLAY button to watch the tape.

Helpful Hints

•You may only set the real-time counter memory at one location at a time. If you set the real-time counter to zero at a second loca- tion, the previous real-time counter to zero setting will be erased.

•To erase the real-time counter memory, press the COUNTER MEMORY button repeatedly so that the M disappears from the screen.

•The COUNTER MEMORY button does not function if AUTO REPEAT is set to [ON]. Details are on page 33.

Image 36

Contents Instruction Book Dear Philips product owner For Customer UseThis bolt of lightning indi- cates uninsulated material Model No Serial NoFeatures Safety PrecautionsIntroduction Declaration of ConformityTable of Contents Putting Batteries in the Remote Control Using the Remote Control HolderVCR maintenance Erasure PreventionUsing the Alarm Clock Putting Batteries in the Alarm ClockUsing the Alarm Clock Holder Setting the Time and the AlarmHookups Without a Cable Box / Direct Broadcast System Disconnect the antenna or cable from your TVCable Signal ConnectionsRecording/Viewing Any Channel Signal Recording One Channel/Watching AnotherCable Box/DBS CableHookups With a Stereo TV Turning on Your VCR Automatic TV Channel Setup Press the Menu button until the main menu appearsAutomatic TV Channel Setup cont’d Adding/Deleting ChannelsSetting the VCR Clock Setting the VCR Clock cont’d Your selection will flash on the screen in the AM/PM spacePress the EXIT/C. Reset button when you are finished Choosing a LanguageOFF mode Press the Display button once Count mode Press the Display button once Clock modeOn-Screen Displays Remote Control Buttons Power ButtonRecord Button Remote Control Buttons cont’d Alarm Clock Power LightTimer Light VCR/TV LightFront Panel AC Power Cord Back PanelAudio OUT Jack Video OUT JackPlaying VHS Quasi Play Back SqpbRead and follow the steps below to play a tape Recording 1Turn on the TV Insert a tapeStarting an OTR Stopping an OTRTimer Recording Details are on page fiveRepeat the procedure in to set the recording’s end time Enter the recording’s start timeTimer Recording cont’d Cancelling a Timer Recording Main menu will appearCorrecting a Timer Recording VCR/TV light will disappear To stop recording, press the Stop buttonRerecording Copying Tapes AntennaRepeat Play Press the Play button or the Stop button repeatedly toSelect Auto Repeat Forward and Reverse Searching/Pausing a Picture Pausing a PictureForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPPicture Select Real-Time Counter Memory Press the Play button to watch the tapeAutomatic Playback Features Helpful Hints Helpful Hints cont’d Renewed Dictionary/Specifications SpecificationsDictionary Index Supplied Accessories