RF-Link Technology RFL NCM manual Specifications, NMS Mode Ascii Character Addressing Format

Page 2

SPECIFICATIONS

As of the date this Instruction Data Sheet was published, the following specifications apply to the RFL NCM Module. Because all of RFL products undergo constant improvement and refinement, these specifications are subject to change without notice.

Live Insertion/Extraction: The NCM Module is capable of live insertion and extraction into the IMUX 2000 shelf without interruption to the DS1 or any other DS0.

Asynchronous Data Interface: Full duplex or half duplex, one channel operation, one or two data ports.

Data Rate: 2400, 4800, 9600, 19.2kbps and *38.4kbps. (*38.4kbps may require character pacing and/or additional stop-bits)

Start-Stop Distortion: Referenced to actual Rx Baud <9%

Gross Start-Stop Distortion: Referenced to nominal Baud <50%

Character Delay: 16 characters max (delay is dependant on input frequency deviation from nominal data rate)

Frequency Deviation: Allowable input Frequency Deviation from nominal data rate is ±4%. (Stop bit reduction is used to compensate for frequencies greater than local oscillator generated baud).

NMS Mode ASCII Character Addressing Format: [0-9][0-9][0-9] [:]

Example: NMS sends “215:”

Time Slots: Occupies one selectable DS0 time slot.

Jitter: Excluding Stop bit <1%

Rogue Detectors: One minute pick-up, two minute drop-out

RS-232 DCE Interface:

Supports: Tx Data, Rx Data, and Signal Ground. Receive Line Signal Detect and Clear to Send are always held active.

RS-485 DCE Interface:

Two-wire: Supports half-duplex, transmit data or receive data, and ground.

Four-wire: Supports full-duplex transmit data, receive data, and ground.

Telnet Interface: Supports: Tx Data and Rx Data over ethernet.

Connector:

For RS-232 the NCM module uses an MA-402I Module Adapter, which provides two DB-9 female connectors.

For RS-485 the NCM module uses an MA-485 Module Adapter, which provides a single, six position terminal block.

For Telnet the NCM module uses a shielded RJ45 connector.

Power Dissipation: 0.5 Watt nominal

MTBF (Calculated): TBD

Operating Temperature: -20oC to +55oC (-4oF to +131oF).

Humidity: 0 to 95 %, non-condensing.

RFL NCM

 

RFL Electronics Inc.

November 6, 2007

2

(973) 334-3100

Page 1 Page 3
Image 2
Page 1 Page 3
Contents RFL NCM RFL NCMDescription Specifications NMS Mode Ascii Character Addressing FormatInstallation RFL NCM MA-402I Module adapter, connector pinouts MA-485 Module adapter, jumper functions and TB1 pinouts MA-490 RFL NCM Front Panel View of RFL NCM, Network Communications Module Typical network example with all nodes having an NCM module At node 3, SW7 is set as follows Controls and indicators, RFL NCM Module Name/Description Function RFL NCM PRA Actel probe a NMS NMSDown SW2-3 SW2-4 Do not move SW10-4 Block diagram, RFL NCM module Functional DescriptionSystem Overview RX Output Ports NCM Backplane and Power ConnectionsTX Input Ports Logic Array Actel DesignSCB Module Application Modes and InterfacesUart Receive Section Uart Transmit Section T1 Transmit ModuleLOOP-BACKS T1 Receive ModuleRogue Control Baud and Clock GeneratorService LED should be illuminated green TestingPower indicator should be lit Test Equipment RequiredDS1 Power indicator should be lit DS1-B Equip OUT RXA LED should be illuminated red CH1 DS1-B Equip OUT CH2 Remote Control Using NMS NCM General Configurations and Status window for NodeTime Slot Module EnableE1 Signaling ModeTypical 3-node network using MA-485s 1 RS-485 port Bus a & Bus B Rogue DetectionNCM Address Configurations and Status window for Node Local CM AddressCM Address Passing Parity Baud RateData Bits Loopback TroubleshootingPort 2 Enable Codes Remote Control Using SCL CommandsChannel Card 3, Type 117 Under Remote Control Svce = on Multiplexer Addresscard ADDRESSSETP1 = B00000011 Srvc = on Srvc = OFFCAS Setting BUS a SettingBUS B Setting Timeslot SelectionParity Settings Port Loopback SettingsBaud Settings Word Length SettingsApplication Mode CM Address Pass SettingsNMS Mode only SettingsCodes Port 1 Availability MUX Type & Configuration StatusType ID Port 2 AvailabilityPort 1 Application Status Application Configuration StatusCM Addressing Support Port 2 Application StatusRXA Remote CM Address Current Actel REVPort 1 INPUT/OUTPUT Status Port 2 INPUT/OUTPUT StatusTXA/RXB Status for T1/E1 TXB/RXA Status for T1/E1Powerville Road

Network Communications Module, RFL NCM specifications

RF-Link Technology has emerged as a significant player in the realm of wireless communication, and one of its standout offerings is the RFL NCM (Network Communications Module). This module is designed to facilitate efficient and reliable data transmission in a variety of applications, making it a versatile solution for both industrial and commercial needs.

The RFL NCM is built on advanced RF technologies that support multiple communication protocols, ensuring compatibility with different systems and devices. One of its main features is its exceptional range. The module is capable of transmitting data over long distances, making it ideal for applications where devices are spread out. This long-range capability is essential for remote monitoring and control tasks, such as in smart agriculture, environmental monitoring, and industrial automation.

Another defining characteristic of the RFL NCM is its low power consumption. The module employs energy-efficient communication methods, enabling devices to operate for extended periods without frequent battery replacements. This makes it particularly useful in applications where power availability is limited or where continuous operation is required without maintenance interruptions.

The RFL NCM supports a variety of communication protocols, including LoRa, Zigbee, and MQTT, providing flexibility for developers and integrators to choose the most suitable technology for their specific applications. Its robust design ensures resilience in various operating conditions, including extreme temperatures and potential environmental hazards like moisture and dust.

Ease of integration is another strong point of the RFL NCM. With extensive documentation and support, developers can quickly incorporate the module into their existing systems. It also features built-in security protocols to safeguard data during transmission, which is particularly important in today’s increasingly connected world where data breaches are a growing concern.

The RFL NCM is not just about performance; it inherently supports scalability, allowing users to expand their network as their needs grow, whether that's adding more sensors to a monitoring system or integrating additional devices in a smart home. This commitment to both performance and adaptability makes the RFL NCM an attractive option for developers looking to harness the power of RF communications.

In summary, the RF-Link Technology RFL NCM stands out due to its long-range capabilities, low power consumption, support for multiple communication protocols, and robust integration features. With applications across various sectors, including industrial, commercial, and residential, this module promises to enhance connectivity and streamline operations in an increasingly wireless world.
Top Page Image Contents