Aiwa AV-D55 manual Setting the Clock, Setting the Sleep Timer, To cancel the sleep timer

Page 18

SETTING THE CLOCK

CLOCK

213

I

VIDEO 1/5:1CH/BAND

When the AC cord is connected for the first time, the clock on the display flashes.

Set the time as follows whila the power is off.

1 Press the ENTER button.

The display becomes a little brighter.

2 Turn the MULTI JOG to designate the hour and the minute.

The time advances by turning it to right, and decreases by turning it to left.

The DOWN or UP button is also available. Press the button repeatedly. To change the time rapidly in 10-minute steps, hold it down.

3 Press the ENTER button.

The clock starts from 00 seconds.

When the clock is set for the first time after purchase Everything on the display will clear.

This is because the power economizing mode of the unit is activated, and is not a malfunction.

The power economizing mode can be canceled. See page 6 for

details.

To correct the current time

Press the POWER button to turn the unit off. Press the ENTER button and cany out steps 1 to 5 above.

To display the current time

Press the CLOCK button on the remote control. The clock is displayed for 4 seconds.

To switch to the 24-hour standard

Press the VIDEO 1/5. 1CH/BAND button while the current time is displayed.

Repeat the same procedure to restore the 12-hour standard.

If the clock display flashes while the power is off

This is caused by a power interruption. The current time needs to be reset.

If power is interrupted for more than approximately 24 hours, all settings stored in memory after purchase need to be reset.

SETTING THE SLEEP TIMER

1

2

The receiver can be automatically turned off at a specified time.

Use the remote control.

1Press the SLEEP button.

2 Press the UP or DOWN button within four seconds to specify the time until the power is turned off.

Each time the button is pressed, the time changes between 5 and 240 minutes in 5-minute steps.

Specified time

The time can also be selected by the MULTI JOG on the main unit.

To check the time remaining until the power is turned off Press the SLEEP button once. The remaining time is displayed

for four seconds.

To cancel the sleep timer

Press the SLEEP button twice so that “SLEEPoFF”on the display appears.

17 ENGLISH

Image 18

Contents Call toll free l-800-BUY-AIWA Electric Power PrecautionsInstallation AC power cordTable of Contents Connecting Equipment ConnectionsSmsalw terminals Connecting Speakers @Connecting + to +, -to terminals Speaker impedanceConnecting the Supplied Antennas @ Connecting AN Outdoor AntennaPositioning the Speakers Aboijt the Remote Control Power Economizing ECO Moide M14Before Operation To turn the unit on Press the Power buttonUsing the headphones To change the brightness level of the displayDOWN,UP Volume VOL Muting Balance T-BASS Volume ControlSound Adjustment During Recording Super T-BASS SystemSetting NEW Equalization Curves Electronic Graphic EqualizerTo select with tlhe remote control When the music source is monauralCancel me seIecIea moae DSP SurroundAbout the video source to the monitor or TV To adjust the sound level of the connected sourceSelection of AUDIO/VIDEO Source To select the video sourceRecording AN Audio Scjrce To Iplay a DVD Recorded in Dolby Digital SurroundTape Monitor Multijog When an FM stereo broadcast contains noise Manual TuningTo change the AM tuning interval To search for a station quickly Auto SearchWhen using the remote control Piresetting StationsPreset Number Tuning ButtonsSelecting Dolby PRO Logic To Select a Dolby PRO Ilogic ModeRecommended mode Check the followingDclby PRO Logic PHANTOMmode Adjusting Speaker Level BalanceDclby PRO Logic Normal or’ Wide mode About the channelsSet the time as follows whila the power is off Setting the ClockSetting the Sleep Timer If the clock display flashes while the power is offAM tuner section Care and MaintenanceFM tuner section Amplifier sectionGeneral Troubleshooting GuideGeneral Tuner SectionParts Index Eneraia electrica PrecaucionesInstalacion Anotacion del propletario3Jos que requieren reparation ~ena exteriorMntenimiento Cornpruebe su unidad y accesorios03 \ ~l==== ConexionesConexion DE Equipos Antes de conectar el cable de alimentacion de CAConexion DE LOS Altavoces @ Surround SpeakersUbicacion DE LOS Altavoces Conexion DE LAS Antenas Suministradas @Conexion DE UNA Antena Exterior SOE3RE EL Controlador Remoto Modo DE Ahorro DE ENERGiA ECOPara cambiar el nivei de brillo del visualizador Antes DE LA OperacionSeleccion del sistema de altavoces delanteros Utilization de auricularesSistema Super T-BASS Control DEL VolumenAjiijste DEL Sonido a SU Gusto Ajuste DEL Soinido DUI?ANTE LA GRABAC16NAjuste DE Nuevas Curvas DE Ecualizacion Ecualizador GraficoElectronic Dentro de 8 segundos, presione el boton EnterPara cancelar el modo seleccionadlo Sonido Perimetrico DEL Procesador DE Senal DigitalCuando la fuente de musics sea monoaural Sobre la fuente de video para el monitor o el televisor Seleccion DE UNA Fuente DEPara seleccionar la fuente de video Para ajustar el nivel del sonido de la fuente conectada1ENTER Grabacion DE UNA Fuente DE AudioSelecciorw la fuente de programas que desee grabar De tres cabezasPara cambiar Ios intervals de sintonizacion de AM Sintonizacion ManualPresione el boton UP o Down para seleccionar una emisora Para buscar una emisora rapidamente Busqueda automaticMemorization DE Emisoras Sintonizacionde Nti MERCl~SMemorizados Seleccion DE Dolby PRO Logic Para Seleccionar UN Modo Dolby PRO LogicModo recomendado Con e! tipo y la ubicacion de sus altavoces Ajuste DEL Equilibria DEL ’EL Entre AltavocesSeleccione el modo Dolby Pro Logic de acuerdo Modo Dolby PRO Logic Normal O WidePresione el boton Sleep Puesta EN Hora DEL RelojGire Multi JOG para designar la hors y Ios minutes Se desconecte la alimentacionSeccion de! sintolnizador de AM Cuiidados Y Mantenimiento EspecificacionesSeccion del sintonizador de FM Seccion Del ampliificadorSeccion General ProblemasGenerales Seccion DEL SintonizadorR4DICE DE Componentes Electricity InstallationAV-D55 Releve du proprietaireHWetien Table DES MatieresAntenne exterieure ~nmaaes exiqeant l’intervention d’un P3essionnelRaccordements Impedance des enceintes LRACCORDEMENT DES Enceintes @Rx%k Raccordement des bornes + a + et aRaccordement D’UNE Antenne Exterieure Positionnement DES EnceintesRaccordement DES Antennes Fournies @ Pour poser I’antenne cadre AM sur une surfacePHI3POS DE LA Telecommande Mode D’ECONOMIE D’ENERGIE ECOSelection de la paire d’enceintes avant Avant DE CommencerPour changer la Iuminosite de I’affichage Utilisation d’un casque d’ecoute’ENREGISTREMENT Iwglage DE VolumeSysteme Super T-BASS Pour ajuster la balance gaucheidroite des enceintes avantEgaliseur Graphique Electronique Reglage DE Nouvelles Courbes D’EGALISATIONPrcesseur D’AMBIANCE Pour annuler Ie mode sdectionnePour selectionner Ie mode avec la t~lecomrnande CJuandla source de musique est monophoniquePour changer Ie nom affiche pour la Video 1 et la Video Selection D’UNE Source Audio OU VideoPour selectionner la source video Pour ajuster Ie niveau sonore de la source raccordeeEnregistreivient D’UNE Source Audio 1ENTER Tape Monitor MultijogSecondes. En tours de reception stereo FM, mms’affiche Accord ManuelPour changer I’intervalle d’accord AM Quand une emission stereo FM est parasiteeAccord D’IJN Numero Pfieregle Avec la telecommandeFwreglage DES Stations Repetez Ies etapes 1 etSelection DU Dolby PRO Logic Pour Selectionner UN Mode Dolby PRO LogicMode conseille Verifiez Ies points suivantsSelect pour arr~ter Ie signal Xdectionnez Ie mode Dolby Pro Logic en fonctionMode Dolby PRO Logic Phantom Reglage DE LA Balance DU Niveau DES EnceintesREGLAGEDEL’HORLOGE ’ARRETSoin ET Entretien Section TunerSection Amplificateur Puissance de sortie Generalities Guide DE DepannageGeneralities Section TunerIndex DES Composants Page