Continued from the front
3 Carry out the AUTO SETUP (IntelliBeam)
Carry out the AUTO SETUP to adjust the settings that best match your listening environment.
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
5Turn on the power of your TV.
6Select the appropriate video input
on your TV.
If the OSD video pin cable is connected to the video input 1 on the TV as shown in the connection example 1, switch the video
11Press ENTER to start the AUTO SETUP procedure, and then leave
the room within 10 seconds.
The following screen appears on the TV. Leave the room within 10 seconds before the AUTO SETUP procedure starts.
ENHANCER | ENTRY | MENU | AUTO SETUP START |
|
|
|
4 | Enjoying surround sound |
Enjoy TV or DVD digital audio in surround sound.
For instructions on how to operate or set your TV or DVD player/recorder, refer to the owner’s manual supplied with each component.
1Assemble the cardboard microphone stand.
Place the IntelliBeam microphone on top of cardboard microphone stand as shown below.
1 | 2 | 3 | 4 |
input to “1”.
7Set the operation mode selector to
YSP.
This unit switches to the YSP operation mode.
ENHANCER ENTRY
MENU
CAT/ | TV/AV | |
ENTER | ||
YSP | ||
|
DISPLAYRETURN
|
| Will begin in 20sec |
CAT/ | TV/AV | Please leave the room |
ENTER |
| |
| ||
YSP | ||
|
| |
DISPLAY | RETURN | [RETURN]:Cancel |
|
The setup screen automatically changes during the AUTO SETUP procedure.
When the AUTO SETUP procedure is completed, the following screen appears on the TV.
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save
Enjoying DVDs in surround sound
1Select the DVD video input on your TV.
2Set the operation mode selector to
YSP.
This unit switches to the YSP operation mode.
Enjoying TV in surround sound
1Select the TV channel using the
remote control supplied with your TV.
Mute the volume on the TV.
2Set the operation mode selector to
YSP.
This unit switches to the YSP operation mode.
2Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC jack on the front panel.
IntelliBeam microphone (supplied)
8Press and hold AUTO SETUP for
more than 2 seconds.
The menu screen appears on the TV.
If “ENVIRONMENT CHECK (FAILED) is displayed, see page 34 in the Owner’s Manual and then run the procedure again.
y Hint |
CAT/ | TV/AV | CAT/ | TV/AV | |
ENTER | ENTER | |||
YSP | YSP | |||
|
| |||
DISPLAY | RETURN | DISPLAY | RETURN |
INTELLIBEAM MIC
Cardboard microphone stand (supplied)
3Set the IntelliBeam microphone at your normal listening position.
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would
If the menu screen does not appear, check the OSD video pin cable (see the connection example on the front page).
FM/XM | CAT | MEMORY | AUTO SETUP |
PRESET/TUNE SEARCH |
| ||
|
|
| PREPARATION & CHECK |
|
|
| Please connect the MIC. |
VOL MODE | AUTO | SLEEP | Please place the MIC at least |
SETUP INPUTMODE | 1.8m/6ft away from the YSP | ||
|
|
| unit. The MIC should be set |
|
|
| at ear level when seated. |
5BEAM | ST+3BEAM 3BEAM | Measurement takes about 3min. | |
1 | 2 | 3 | After [ENTER] is pressed, |
please leave the room. | |||
[ENTER]:Start [RETURN]:Cancel
• The result may differ depending on the environment. |
• If any error occurs, the corresponding error message appears |
on the screen. In this case, see “Error messages for AUTO |
SETUP” on page 35 in the Owner’s Manual and then follow |
the instructions. To start the AUTO SETUP procedure once |
again, press RETURN. |
12Press ENTER.
31) Press DVD on the remote
control of this unit.
This unit switches to the DVD playback mode.
DVD
AUX1 AUX2 AUX3
INPUT1 TV MACRO
STB TV
PRESET/TUNE SEARCH MEMORY
2) Play back the supplied demonstration |
DVD on the DVD player/recorder. |
3Press TV on the remote control of
this unit.
This unit switches to the TV playback mode.
INPUT1 MACRO
STB TV 
PRESET/TUNE SEARCH MEMORY
FM/XM CAT
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM ST+3BEAM 3BEAM
1 2 3
be when you are seated.
IntelliBeam
Upper bound
microphone
position of the
Place the IntelliBeam microphone on the extended center line of this unit and 1.8 m (6.0 ft) or more away from it. Also, make sure place the IntelliBeam microphone within 1 m (3.3 ft) upper or lower from the center height of this unit.
9Check the following points.
About the IntelliBeam microphone
• Is the microphone placed on an imaginary center line drawn |
from this unit? |
• Is the microphone placed within 1 m (3.3 ft) upper or lower |
The following screen appears on the TV for 2 seconds and then the menu screen disappears from the TV.
ENHANCER ENTRY
MENU
|
| AUTO SETUP COMPLETE |
CAT/ | TV/AV | Please remove the MIC from |
4Check the digital signal being output at this unit.
The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they
Input channel indicators
Center height of this unit
microphone
from the center height of this unit? |
• Is the microphone placed more than 1.8 m (6.0 ft) from the |
ENTER | YSP | the YSP and the listening | |
| position. | ||
|
|
| |
DISPLAY |
| RETURN |
|
switch according to the channel composition of the corresponding input source. If the sound is output from your TV speakers, mute the volume on your TV. For details about digital audio input signals, see page 58 in the
| Within 1 m (3.3 ft) |
Cardboard | Within 1 m (3.3 ft) |
Listening |
Center line
IntelliBeam
front of this unit? |
About the room environment
• Is your listening room kept as quiet as possible?
Owner’s Manual.
microphone stand |
| position |
More than 1.8 m (6.0 ft) |
| Lower bound position |
| ||
|
| |
|
| of the microphone |
Cardboard microphone stand
microphone
10Prepare to leave the room.
13Disconnect the IntelliBeam
microphone.
5 Press VOLUME +/- on the remote control to adjust the |
volume level of this unit. |
VOLUME | CH | TV VOL |
MUTE | TV INPUT | TV MUTE |
4Press STANDBY/ON on the remote control.
The power of this unit turns on. |
|
|
Before operations, insert batteries into the remote |
|
|
control (see page 24 in the Owner’s Manual). |
|
|
If necessary, adjust the volume level of this unit. | STANDBY/ON | POWER POWER |
If you have connected the subwoofer, set the volume and crossover/high cut frequency. Refer to the “Notes” on page 30 in the Owner’s Manual.
Subwoofer
The best setting may not be done if you are in the room. Prepare to leave the room in 10 seconds after pressing ENTER in step 11.
y Hint |
• When leaving the room, bring this guide with you. |
The AUTO SETUP has completed. Keep the IntelliBeam microphone in a safe place.
The settings are automatically saved in the system memory.
6 Press one of the beam mode buttons on the remote control to |
select the desired beam mode. |
5BEAM ST+3BEAM 3BEAM
1 2 3
STEREO MY BEAM MY SUR.
|
| TV | AV |
|
|
| DOCK |
DVD | AUX1 | AUX2 | AUX3 |
|
|
| TV |
VOLUMECROSSOVER/ HIGH CUT
MIN | MAX | MIN | MAX |
• Wait outside the room during the AUTO SETUP procedure. |
• The AUTO SETUP procedure takes about 3 minutes. |
• To cancel the AUTO SETUP procedure after it is started, |
press RETURN. |
INTELLIBEAM MIC
Select one of the six beam modes that best matches the current input source of this unit. | 4 | 5 | 6 |
For further information on the beam modes, see pages 56, 57, 62, 63 and 64 in the Owner’s Manual. |
|
|
|
To
beams, etc., see “MANUAL SETUP” on page 74 in the Owner’s Manual.