Pelco DD53TC16-X manual Zones

Page 30
Zones

Zones

SPECTRA III

LANGUAGEENGLISH

<SYSTEM INFORMATION> <DISPLAY SETUP>

<DOME SETTINGS> ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD>

BACK

EXIT

ZONES

ZONE NUMBER

1

* * * ZONE NOT DEFINED * * *

 

<EDIT ZONE LABEL>

 

<EDIT ZONE>

 

ZONE ENABLED

NO

ZONE BLANKING

OFF

<CLEAR ZONE>

 

BACK

 

EXIT

 

*This setting only applies to Pressurized Spectra III dome systems with software version 1.25 or higher.

A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra dome system is capable of eight zones, each with a 20-character label.

To program a zone:

1.Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open the cursor moves to the right.

2.Move the joystick up or down to view selections. Press Iris Open to enter selection.

3.Use the joystick to position the cursor beside EDIT ZONE.

4.Press Iris Open. The Zone programming window appears on the monitor.

5.Follow the directions displayed on the monitor. After the left and right limit stops are set, the Zones menu reappears with the ZONE ENABLED option set to YES.

To edit a zone label:

 

1.

Use the joystick to position the cursor beside EDIT ZONE LABEL.

2.

Press Iris Open. The following appears on the monitor:

 

LABEL FOR ZONE

 

 

ZONE NUMBER ------

OK

 

1234567890

 

ABCDEFGHIJ

CANCEL

 

KLMNOPQRST

 

 

UVWXYZ.,-/

SPACE

 

abcdefghij

BACKSPACE

 

klmnopqrst

 

 

uvwxyz#&:*

 

3.Use the joystick to position the cursor beside a character. Press Iris Open to enter selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris Open.

4.When the label is completed, move the cursor the OK. Press Iris Open to return to the Zones menu.

To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:

1.Move the cursor beside ZONE ENABLED or ZONE BLANKING.

2.Press Iris Open. The cursor moves to the right.

3.Move the joystick up or down to view selections. Press Iris Open to enter selection.

To clear a zone:

1.Use the joystick to position the cursor beside CLEAR ZONE.

2.Press Iris Open. Follow the instructions on the screen.

30

C2446M-E (11/05)

Image 30
Contents O P E R AT I O N / P R O G R A M M I N G Spectra III SeriesModels DD53TC16 & DD53TC16-X C2446M-E11/05Page OPERATION/PROGRAMMING MANUAL MODELS DD53TC16 & DD53TC16-X16X LowLight COLOR TECHNOLOGY C2446M-E11/05 CONTENTS POWER UP WELCOME Getting StartedPresets HOW TO OPERATE YOUR DOME SYSTEMHow to Control AlarmsKBD200A/KBD300A Direct Mode Only Accessing Main Menu PresetCM6700/CM6800 CM9500NET300/NET350/NET4001A KBD4000/KBD4002MPT9500 WS5050Presets Preset FunctionQUICK START GUIDE - SYSTEM SETUP Press Iris Close to cancel selectionC2446M-E11/05 LANGUAGE Quick Programming GuideSYSTEM INFORMATION DISPLAY SETUP Quick Programming GuideLabel Position AUTO FOCUS DOME SETTINGSCamera ZOOM LIMITAdvanced Camera Settings SHUTTER SPEEDAGC LIMIT Auto Iris Peak AUTO IRISAuto Iris Level Quick Programming GuideThere are two settings AUTO SHARPNESSAUTO WHITE BALANCE ON defaultQuick Programming Guide BACKLIGHT COMPENSATION BLCVIDEO LEVEL Backlight compensation is not activatedMotion Settings AUTO FLIPPROPORTIONAL PAN Dome goes to preset PARK TIMEPark Action Quick Programming GuideSCAN SPEED LIMIT STOPS2.Press Iris Open AZIMUTH ZEROTo program azimuth zero 3.Follow the directions displayed on the monitorPower Up POWER UP ACTIONLine Sync Quick Programming GuidePresets PresetAction Patterns Quick Programming GuideZones Title Text Quick Programming GuideSystem Condition AlertREPEAT Alert MessageACTIVATE AUX RESET ALERTACK ACTION CURRENT READINGREBOOT SYSTEM EXIT DOME SETTINGS CAMERA ClearACK ALERT RESET CAMERA CYCLE CAMERA POWER BACK EXIT CLEAR RESTORE FACTORY DEFAULTS BACKPassword Quick Programming GuideCYCLE CAMERA POWER RESET, CYCLE POWER, REBOOTRESET CAMERA REBOOT SYSTEMSOFTWARE/LANGUAGE FILE UPLOAD UPLOAD ICONUpload Icon SPECIFICATIONS DD53TC16DD53TC16-X REGULATORY NOTICES RADIO AND TELEVISION INTERFERENCEREVISION HISTORY Page Page Tel 800/289-9100 Fax 800/289-9150 International World Headquarters 3500 Pelco WayClovis, California 93612 USA USA & Canada Tel: 1-559/292-1981 Fax: 1-559/348-1120
Related manuals
Manual 42 pages 54.13 Kb