Pelco 9770 manual CM9700-MGR PC Pin-Out Detail

Page 30

CM9700-MGR		CM9700-CC1
PC COM PORT	RS-232 CABLE	COM 1/COM 2
	RS-232 CABLE
PIN 3 (TX)		PIN 2 (RX)
PIN 2 (RX)		PIN 3 (TX)
PIN 5 (GND)		PIN 5 (GND)
DB9 FEMALE		DB9 FEMALE

Figure 22. CM9700-MGR PC Pin-Out Detail

6.Install any additional system peripheral devices. Refer to the manuals for the individual devices for instructions. Refer to the Data Connections section and your Port Assignments table for directions on which port to use for each device.

7.Connect all power line cords to the equipment. Do not turn on the power until the installation is complete. Refer to the System Start-Upsection.

30	C1555M-G (12/07)

Image 30

Contents System C1555M-G 12/07 Contents List of Illustrations List of Tables Description Matrix Bay ModelsController and CPU Components Network Interface UnitKeyboards Optional ComponentsCompatible Receivers CM9700-CC1 InstallationUnpacking CM9770-MXBMounting CM9770-MXB Mounting BaffleMounting the CM9770-MXB on Top of the Mounting Baffle Mounting the CM9700-CC1 Video INPUT/OUTPUT Connections Opening the CM9770-MXB Front CoverInsert or Replace a Video Card Installing Video Input Cards CM9770-VCCHow to Turn On the Pelco V-Sync Signal Remove a Video CardInstalling Monitor Output Cards CM9770-VMC Insert or Replace a Monitor CardRemove a Monitor Card Color Diagnostic Check Performing a Basic LED CheckTable A. LEDs Illuminated During a Basic Check Installing Rear Panel BNC Cards Insert or Replace a Rear Panel Video BNC Card CM9770-RPCRemove a Rear Panel Video BNC Card CM9770-RPC CM9770-RPC Termination Jumpers-Right Card Looping Video Looping Video Out from the CM9770-MXBInsert or Replace a Rear Panel Monitor BNC Card CM9770-RPM Video INPUT/OUTPUT Capacity Single BayMultiple Bays, Single Node Sample Sideframing System Using an Output Bay Sample Single-Node System with Downframing Networked System Sample Networked SystemPower Supply Module CM9700-MPS Install a Backup Power SupplyRemove a Backup Power Supply HOW to Replace the Fuse in a Power Supply Module How to Replace a Power Supply FuseHOW to Turn OFF the Audible Power Supply Alarm Power Supply Alarm Speaker SwitchSystem Device Connections CM9700-CC1 Device ConnectionsCM9700-MGR PC Pin-Out Detail RS-422 COM Port Sercom Connections As necessary NIU connectionNot have to be in sequential ports Switch NIU connection Table D. Data Connections-Single Node, Hot-Switched SystemSwitch MXB connectionsSample CM9770-MXB to CM9700-CC1 Connection System Start-Up Initialize the CC1Verify System Operation Initialize KeyboardsMonitor Color Adjustment Display the CM9770-MXB Software Version LevelDisplay a Blue Raster Screen Programming Your System Getting Help Using CM9700-MGR Sample WizardOperation Operating Your SystemHOW to Expand Your System AppendixSystem Architecture Sideframing Downframing Downframing with DFC Cards Downframe Cards DFC Card HOW to Install or Replace a CM9700-SER Card in the CC1 ISA Slot Number W1 IRQ SettingHow to Install a CM9700-SER Card When LED Is On Video Input Card CM9770-VCC DetailColor When LED is on or blinking Monitor Output Card CM9770-VMC DetailPort 1 RS-422 Baud Rate Test ModeColor System Data ProtectionNetworking Connecting Satellite Devices Programming Satellite DevicesHOW to Install Video Patch Panels CM9700-VPP CM9700-VPP Vertical MountMounting the CM9770-MXB in AN Open Rack Mounting the CM9770-MXB in an Open RackAUTOEXEC.BAT and the Boot Process DOS Environment and Command ReferenceBoot Process Invoking the CM9700 ExecutableNavigating the DOS Directory Tree DOS CommandsFile Names and DOS Example PATH=c\c\dosc\windowsExample Using the Wild Card CharacterManipulating Files in the DOS Environment Change to the 9700 directoryDOS Reference \CDBackslash \ symbol Help commandFloppy of a disk formatted using this switch By default, DOS searchers just the current directorySymptom Possible Cause Corrective Action TroubleshootingProblems with the CC1 VCC Card CF LED Is Illuminated and the AUX LED Is BlinkingSwitch Monitor Display ProblemsLED Indicators on the Power Supply Module Front Panel Label ColorSpecifications Input Voltage Differential Gain 51% Differential Phase DegreesSignal to Noise Ratio 71dBrms CommunicationRegulatory Notices CM9780-MXBProduct Warranty and Return Information ISO9001