Pelco 9770 manual HOW to Install Video Patch Panels CM9700-VPP, CM9700-VPP Vertical Mount

Page 53

HOW TO INSTALL VIDEO PATCH PANELS (CM9700-VPP)

There are two ways you can mount a CM9700-VPP video patch panel into a rack.

1.Single panels onto a rack

2.Up to 16 panels using the CM9700-VPP-RK

The following illustration shows how to mount a single panel onto a rack. The panel is mounted horizontally.

CABLE BRACKET

CM9700-VPP

(4)SCREWS, 10-32X3, PHILLIPS PANHEAD WITH WASHERS

RACK

RACK

MOUNT

BRACKET

Figure 44. CM9700-VPP Horizontal Mount

The following illustration shows how to mount up to 16 panels using the CM9700-VPP-RK. The panels are mounted vertically in the CM9700-VPP- RK. This rack saves 1 RU of space and provides better cable management.

THUMBSCREW

RACK

CM9700-VPP (MAXIMUM OF 16)

THUMBSCREW

CM9700-VPP-RK

(8) SCREWS, 10-32X3, PHILLIPS

PANHEAD WITH WASHERS (4 EACH SIDE)

Figure 45. CM9700-VPP Vertical Mount

C1555M-G (12/07)

53

Image 53

Contents System C1555M-G 12/07 Contents List of Illustrations List of Tables Description Controller and CPU Components ModelsMatrix Bay Network Interface UnitCompatible Receivers KeyboardsOptional Components Unpacking InstallationCM9700-CC1 CM9770-MXBCM9770-MXB Mounting Baffle MountingMounting the CM9770-MXB on Top of the Mounting Baffle Mounting the CM9700-CC1 Opening the CM9770-MXB Front Cover Video INPUT/OUTPUT ConnectionsHow to Turn On the Pelco V-Sync Signal Installing Video Input Cards CM9770-VCCInsert or Replace a Video Card Remove a Video CardRemove a Monitor Card Installing Monitor Output Cards CM9770-VMCInsert or Replace a Monitor Card Table A. LEDs Illuminated During a Basic Check Color Diagnostic CheckPerforming a Basic LED Check Remove a Rear Panel Video BNC Card CM9770-RPC Installing Rear Panel BNC CardsInsert or Replace a Rear Panel Video BNC Card CM9770-RPC CM9770-RPC Termination Jumpers-Right Card Looping Video Out from the CM9770-MXB Looping VideoInsert or Replace a Rear Panel Monitor BNC Card CM9770-RPM Single Bay Video INPUT/OUTPUT CapacityMultiple Bays, Single Node Sample Sideframing System Using an Output Bay Sample Single-Node System with Downframing Sample Networked System Networked SystemRemove a Backup Power Supply Power Supply Module CM9700-MPSInstall a Backup Power Supply How to Replace a Power Supply Fuse HOW to Replace the Fuse in a Power Supply ModulePower Supply Alarm Speaker Switch HOW to Turn OFF the Audible Power Supply AlarmCM9700-CC1 Device Connections System Device ConnectionsCM9700-MGR PC Pin-Out Detail Not have to be in sequential ports RS-422 COM Port Sercom ConnectionsAs necessary NIU connection Switch Table D. Data Connections-Single Node, Hot-Switched SystemSwitch NIU connection MXB connectionsSample CM9770-MXB to CM9700-CC1 Connection Initialize the CC1 System Start-UpInitialize Keyboards Verify System OperationDisplay a Blue Raster Screen Monitor Color AdjustmentDisplay the CM9770-MXB Software Version Level Programming Your System Sample Wizard Getting Help Using CM9700-MGROperating Your System OperationSystem Architecture HOW to Expand Your SystemAppendix Sideframing Downframing Downframing with DFC Cards Downframe Cards DFC Card ISA Slot Number W1 IRQ Setting HOW to Install or Replace a CM9700-SER Card in the CC1How to Install a CM9700-SER Card Video Input Card CM9770-VCC Detail When LED Is OnMonitor Output Card CM9770-VMC Detail Color When LED is on or blinkingColor System Test ModePort 1 RS-422 Baud Rate Data ProtectionNetworking Programming Satellite Devices Connecting Satellite DevicesCM9700-VPP Vertical Mount HOW to Install Video Patch Panels CM9700-VPPMounting the CM9770-MXB in an Open Rack Mounting the CM9770-MXB in AN Open RackBoot Process DOS Environment and Command ReferenceAUTOEXEC.BAT and the Boot Process Invoking the CM9700 ExecutableFile Names and DOS DOS CommandsNavigating the DOS Directory Tree Example PATH=c\c\dosc\windowsManipulating Files in the DOS Environment Using the Wild Card CharacterExample Change to the 9700 directory\CD DOS ReferenceFloppy of a disk formatted using this switch Help commandBackslash \ symbol By default, DOS searchers just the current directoryProblems with the CC1 TroubleshootingSymptom Possible Cause Corrective Action VCC Card CF LED Is Illuminated and the AUX LED Is BlinkingLED Indicators on the Power Supply Module Monitor Display ProblemsSwitch Front Panel Label ColorSpecifications Signal to Noise Ratio 71dBrms Differential Gain 51% Differential Phase DegreesInput Voltage CommunicationCM9780-MXB Regulatory NoticesProduct Warranty and Return Information ISO9001