Pelco manual Display the CM9770-MXB Software Version Level, Display a Blue Raster Screen

Page 36

DISPLAY THE CM9770-MXB SOFTWARE VERSION LEVEL

To display the software version level on a system monitor, complete the following steps:

1.Enter the monitor number, and then press the MON key.

2.Enter 999997, and then press the CAM key. The software version number appears on the monitor.

DISPLAY A BLUE RASTER SCREEN

To display a blue raster screen on a system monitor, complete the following steps:

1.Enter the monitor number, and then press the MON key.

2.Enter 999999, and then press the CAM key. A blue raster screen appears on the monitor.

MONITOR COLOR ADJUSTMENT

Once you have connected all devices and powered the system, you can use the System 9770 color bars as a reference tool for adjusting the color on each monitor.

1.Enter the monitor number, and then press the MON key.

2.Enter 999998, and then press the CAM key. Broadcast quality color bars appear on the monitor.

3.Adjust color on each monitor as necessary until the color bars match the following color order on the monitor (for black and white monitors you can use the color bars to adjust brightness).

WHITE

YELLOW

CYAN (LIGHT BLUE)

GREEN

MAGENTA (LIGHT PURPLE)

RED

BLUE

BLACK

Figure 26. System 9770 Color Bars

NOTE: You can also set DIP switches 5 and 6 on the monitor output card to display color bars. Refer to the Monitor Output Card (CM9770-VMC) Detail section in the Appendix.

36	C1555M-G (12/07)

Image 36

Contents System C1555M-G 12/07 Contents List of Illustrations List of Tables Description Models Controller and CPU ComponentsMatrix Bay Network Interface UnitKeyboards Optional ComponentsCompatible Receivers Installation UnpackingCM9700-CC1 CM9770-MXBMounting CM9770-MXB Mounting BaffleMounting the CM9770-MXB on Top of the Mounting Baffle Mounting the CM9700-CC1 Video INPUT/OUTPUT Connections Opening the CM9770-MXB Front CoverInstalling Video Input Cards CM9770-VCC How to Turn On the Pelco V-Sync SignalInsert or Replace a Video Card Remove a Video CardInstalling Monitor Output Cards CM9770-VMC Insert or Replace a Monitor CardRemove a Monitor Card Color Diagnostic Check Performing a Basic LED CheckTable A. LEDs Illuminated During a Basic Check Installing Rear Panel BNC Cards Insert or Replace a Rear Panel Video BNC Card CM9770-RPCRemove a Rear Panel Video BNC Card CM9770-RPC CM9770-RPC Termination Jumpers-Right Card Looping Video Looping Video Out from the CM9770-MXBInsert or Replace a Rear Panel Monitor BNC Card CM9770-RPM Video INPUT/OUTPUT Capacity Single BayMultiple Bays, Single Node Sample Sideframing System Using an Output Bay Sample Single-Node System with Downframing Networked System Sample Networked SystemPower Supply Module CM9700-MPS Install a Backup Power SupplyRemove a Backup Power Supply HOW to Replace the Fuse in a Power Supply Module How to Replace a Power Supply FuseHOW to Turn OFF the Audible Power Supply Alarm Power Supply Alarm Speaker SwitchSystem Device Connections CM9700-CC1 Device ConnectionsCM9700-MGR PC Pin-Out Detail RS-422 COM Port Sercom Connections As necessary NIU connectionNot have to be in sequential ports Table D. Data Connections-Single Node, Hot-Switched System SwitchSwitch NIU connection MXB connectionsSample CM9770-MXB to CM9700-CC1 Connection System Start-Up Initialize the CC1Verify System Operation Initialize KeyboardsMonitor Color Adjustment Display the CM9770-MXB Software Version LevelDisplay a Blue Raster Screen Programming Your System Getting Help Using CM9700-MGR Sample WizardOperation Operating Your SystemHOW to Expand Your System AppendixSystem Architecture Sideframing Downframing Downframing with DFC Cards Downframe Cards DFC Card HOW to Install or Replace a CM9700-SER Card in the CC1 ISA Slot Number W1 IRQ SettingHow to Install a CM9700-SER Card When LED Is On Video Input Card CM9770-VCC DetailColor When LED is on or blinking Monitor Output Card CM9770-VMC DetailTest Mode Color SystemPort 1 RS-422 Baud Rate Data ProtectionNetworking Connecting Satellite Devices Programming Satellite DevicesHOW to Install Video Patch Panels CM9700-VPP CM9700-VPP Vertical MountMounting the CM9770-MXB in AN Open Rack Mounting the CM9770-MXB in an Open RackDOS Environment and Command Reference Boot ProcessAUTOEXEC.BAT and the Boot Process Invoking the CM9700 ExecutableDOS Commands File Names and DOSNavigating the DOS Directory Tree Example PATH=c\c\dosc\windowsUsing the Wild Card Character Manipulating Files in the DOS EnvironmentExample Change to the 9700 directoryDOS Reference \CDHelp command Floppy of a disk formatted using this switchBackslash \ symbol By default, DOS searchers just the current directoryTroubleshooting Problems with the CC1Symptom Possible Cause Corrective Action VCC Card CF LED Is Illuminated and the AUX LED Is BlinkingMonitor Display Problems LED Indicators on the Power Supply ModuleSwitch Front Panel Label ColorSpecifications Differential Gain 51% Differential Phase Degrees Signal to Noise Ratio 71dBrmsInput Voltage CommunicationRegulatory Notices CM9780-MXBProduct Warranty and Return Information ISO9001