Pelco 9770 manual Regulatory Notices, CM9780-MXB

Page 64

Regulatory Notices

CM9780-MXB

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CM9700-CC1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this equipment under Federal Communications Commission’s rules.

In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and television reception.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

64

C1555M-G (12/07)

Page 63 Page 65
Image 64
Page 63 Page 65
Contents System C1555M-G 12/07 Contents List of Illustrations List of Tables Description Models Controller and CPU ComponentsMatrix Bay Network Interface UnitOptional Components KeyboardsCompatible Receivers Installation UnpackingCM9700-CC1 CM9770-MXBMounting CM9770-MXB Mounting BaffleMounting the CM9770-MXB on Top of the Mounting Baffle Mounting the CM9700-CC1 Video INPUT/OUTPUT Connections Opening the CM9770-MXB Front CoverInstalling Video Input Cards CM9770-VCC How to Turn On the Pelco V-Sync SignalInsert or Replace a Video Card Remove a Video CardInsert or Replace a Monitor Card Installing Monitor Output Cards CM9770-VMCRemove a Monitor Card Performing a Basic LED Check Color Diagnostic CheckTable A. LEDs Illuminated During a Basic Check Insert or Replace a Rear Panel Video BNC Card CM9770-RPC Installing Rear Panel BNC CardsRemove a Rear Panel Video BNC Card CM9770-RPC CM9770-RPC Termination Jumpers-Right Card Looping Video Looping Video Out from the CM9770-MXBInsert or Replace a Rear Panel Monitor BNC Card CM9770-RPM Video INPUT/OUTPUT Capacity Single BayMultiple Bays, Single Node Sample Sideframing System Using an Output Bay Sample Single-Node System with Downframing Networked System Sample Networked SystemInstall a Backup Power Supply Power Supply Module CM9700-MPSRemove a Backup Power Supply HOW to Replace the Fuse in a Power Supply Module How to Replace a Power Supply FuseHOW to Turn OFF the Audible Power Supply Alarm Power Supply Alarm Speaker SwitchSystem Device Connections CM9700-CC1 Device ConnectionsCM9700-MGR PC Pin-Out Detail As necessary NIU connection RS-422 COM Port Sercom ConnectionsNot have to be in sequential ports Table D. Data Connections-Single Node, Hot-Switched System SwitchSwitch NIU connection MXB connectionsSample CM9770-MXB to CM9700-CC1 Connection System Start-Up Initialize the CC1Verify System Operation Initialize KeyboardsDisplay the CM9770-MXB Software Version Level Monitor Color AdjustmentDisplay a Blue Raster Screen Programming Your System Getting Help Using CM9700-MGR Sample WizardOperation Operating Your SystemAppendix HOW to Expand Your SystemSystem Architecture Sideframing Downframing Downframing with DFC Cards Downframe Cards DFC Card HOW to Install or Replace a CM9700-SER Card in the CC1 ISA Slot Number W1 IRQ SettingHow to Install a CM9700-SER Card When LED Is On Video Input Card CM9770-VCC DetailColor When LED is on or blinking Monitor Output Card CM9770-VMC DetailTest Mode Color SystemPort 1 RS-422 Baud Rate Data ProtectionNetworking Connecting Satellite Devices Programming Satellite DevicesHOW to Install Video Patch Panels CM9700-VPP CM9700-VPP Vertical MountMounting the CM9770-MXB in AN Open Rack Mounting the CM9770-MXB in an Open RackDOS Environment and Command Reference Boot ProcessAUTOEXEC.BAT and the Boot Process Invoking the CM9700 ExecutableDOS Commands File Names and DOSNavigating the DOS Directory Tree Example PATH=c\c\dosc\windowsUsing the Wild Card Character Manipulating Files in the DOS EnvironmentExample Change to the 9700 directoryDOS Reference \CDHelp command Floppy of a disk formatted using this switchBackslash \ symbol By default, DOS searchers just the current directoryTroubleshooting Problems with the CC1Symptom Possible Cause Corrective Action VCC Card CF LED Is Illuminated and the AUX LED Is BlinkingMonitor Display Problems LED Indicators on the Power Supply ModuleSwitch Front Panel Label ColorSpecifications Differential Gain 51% Differential Phase Degrees Signal to Noise Ratio 71dBrmsInput Voltage CommunicationRegulatory Notices CM9780-MXBProduct Warranty and Return Information ISO9001
Top Page Image Contents