Pelco 9770 manual How to Install a CM9700-SER Card

Page 47

PIN 2

PIN 1

W1 IRQ SELECT

PIN 22

PIN 21

IRQ 3

IRQ 4

IRQ 5

IRQ 6

IRQ 7

IRQ 9

IRQ 10

IRQ 11

IRQ 12

IRQ 14

IRQ 15

W2 ADDRESS

SELECT

PIN 2

PIN 1

PIN 4

PIN 3

Figure 37. SER Card Jumper Assignments

4.Insert the new SER card into an available ISA slot. The default CM9700-CC1 configuration provides SER cards in ISA slots 1 and 2, so you will most likely insert the new card into slot 3 or 4. Refer to Figure 38.

5.Replace the top cover of the CC1.

6.Power up the CC1.

CM9700-SER CARD ACCESS SLOTS (SLOT COVERS REMOVED)

SLOT

COVERS

ISA SLOTS (DEFAULT

CM9700-SER CARDS SUPPLIED

IN ISA SLOTS 1 AND 2)

CM9700-CC1 CHASSIS, FRONT

Figure 38. How to Install a CM9700-SER Card

C1555M-G (12/07)

47

Image 47
Contents System C1555M-G 12/07 Contents List of Illustrations List of Tables Description Network Interface Unit ModelsController and CPU Components Matrix BayCompatible Receivers KeyboardsOptional Components CM9770-MXB InstallationUnpacking CM9700-CC1CM9770-MXB Mounting Baffle MountingMounting the CM9770-MXB on Top of the Mounting Baffle Mounting the CM9700-CC1 Opening the CM9770-MXB Front Cover Video INPUT/OUTPUT ConnectionsRemove a Video Card Installing Video Input Cards CM9770-VCCHow to Turn On the Pelco V-Sync Signal Insert or Replace a Video CardRemove a Monitor Card Installing Monitor Output Cards CM9770-VMCInsert or Replace a Monitor Card Table A. LEDs Illuminated During a Basic Check Color Diagnostic CheckPerforming a Basic LED Check Remove a Rear Panel Video BNC Card CM9770-RPC Installing Rear Panel BNC CardsInsert or Replace a Rear Panel Video BNC Card CM9770-RPC CM9770-RPC Termination Jumpers-Right Card Looping Video Out from the CM9770-MXB Looping VideoInsert or Replace a Rear Panel Monitor BNC Card CM9770-RPM Single Bay Video INPUT/OUTPUT CapacityMultiple Bays, Single Node Sample Sideframing System Using an Output Bay Sample Single-Node System with Downframing Sample Networked System Networked SystemRemove a Backup Power Supply Power Supply Module CM9700-MPSInstall a Backup Power Supply How to Replace a Power Supply Fuse HOW to Replace the Fuse in a Power Supply ModulePower Supply Alarm Speaker Switch HOW to Turn OFF the Audible Power Supply AlarmCM9700-CC1 Device Connections System Device ConnectionsCM9700-MGR PC Pin-Out Detail Not have to be in sequential ports RS-422 COM Port Sercom ConnectionsAs necessary NIU connection MXB connections Table D. Data Connections-Single Node, Hot-Switched SystemSwitch Switch NIU connectionSample CM9770-MXB to CM9700-CC1 Connection Initialize the CC1 System Start-UpInitialize Keyboards Verify System OperationDisplay a Blue Raster Screen Monitor Color AdjustmentDisplay the CM9770-MXB Software Version Level Programming Your System Sample Wizard Getting Help Using CM9700-MGROperating Your System OperationSystem Architecture HOW to Expand Your SystemAppendix Sideframing Downframing Downframing with DFC Cards Downframe Cards DFC Card ISA Slot Number W1 IRQ Setting HOW to Install or Replace a CM9700-SER Card in the CC1How to Install a CM9700-SER Card Video Input Card CM9770-VCC Detail When LED Is OnMonitor Output Card CM9770-VMC Detail Color When LED is on or blinkingData Protection Test ModeColor System Port 1 RS-422 Baud RateNetworking Programming Satellite Devices Connecting Satellite DevicesCM9700-VPP Vertical Mount HOW to Install Video Patch Panels CM9700-VPPMounting the CM9770-MXB in an Open Rack Mounting the CM9770-MXB in AN Open RackInvoking the CM9700 Executable DOS Environment and Command ReferenceBoot Process AUTOEXEC.BAT and the Boot ProcessExample PATH=c\c\dosc\windows DOS CommandsFile Names and DOS Navigating the DOS Directory TreeChange to the 9700 directory Using the Wild Card CharacterManipulating Files in the DOS Environment Example\CD DOS ReferenceBy default, DOS searchers just the current directory Help commandFloppy of a disk formatted using this switch Backslash \ symbolVCC Card CF LED Is Illuminated and the AUX LED Is Blinking TroubleshootingProblems with the CC1 Symptom Possible Cause Corrective ActionFront Panel Label Color Monitor Display ProblemsLED Indicators on the Power Supply Module SwitchSpecifications Communication Differential Gain 51% Differential Phase DegreesSignal to Noise Ratio 71dBrms Input VoltageCM9780-MXB Regulatory NoticesProduct Warranty and Return Information ISO9001