JAI CV-A60 operation manual CV-A50/60 RS-232C command list, Timing and shutter related commands

CV-A50 / CV-A60

7.2. CV-A50/60 RS-232C command list.

		Command Name		Format	Parameter		Remarks
	A –		General settings and useful commands
EB		Echo Back		EB=[Param.]<CR><LF>	0=Echo off	1=Echo on	Off at power up
ST		Camera Status request		ST?<CR><LF>			Actual setting
HP		Online Help request		HP?<CR><LF>			Command list
VN		Firmware version		VN?<CR><LF>			3 letter version
	B – Timing and shutter related commands
SC		Scanning format		SC=[Param.]<CR><LF>	0=Interlaced	1=Non-interl.	Partial scanning is
					2=1/2 partial	3=1/3 partial	not supported
TR		Trigger mode		TR=[Param.]<CR><LF>	0=normal	1=Edge
					2=Pulse width	3=Frame delay
					4=Long time	5=Start/stop
SM		Shutter mode		SM=[Param.]<CR><LF>	0=Normal	1=Programmab.
SH		Shutter speed		SH=[Param.]<CR><LF>	0=Off	1=1/100	Continuous only
					0=1/50 (1/60)	1=1/125	Trigger modes and
					2=1/250	3=1/500	Continuous
					4=1/1000	5=1/2000
					6=1/4000	7=1/10000
PE		Programmable expos.		PE=[Param.]<CR><LF>	0= No function	1=1.5H	CCIR. H=64µsec
					1023=1023.5H		EIA, H=63.5µsec
							*1)
	C – Signals and polarity
FR		Accumulation		FR=[Param.]<CR><LF>	0=Field	1=Frame
PC		Pixel clock		PC=[Param.]<CR><LF>	0=no clock out	1=clock out	Should be off
							when not used
TP		Trigger polarity		TP=[Param.]<CR><LF>	0= active low	1= active high	*2)
WP		WEN polarity		WP=[Param.]<CR><LF>	0= active low	1= active high
	D – Gain and analogue signals setting
AS		AGC Switch		AS=[Param.]<CR><LF>	0=AGC off	1=AGC on	0= manual gain
AG		AGC Level		AG=[Param.]<CR><LF>	0=low	255=high	Range 0 to 255
GA		Manual gain Level		GA=[Param.]<CR><LF>	0=low	255=high	Range 0 to 255
RP		Rear Potentiometer		RP=[Param.]<CR><LF>	0=manual gain	1=rear potm.
SU		Setup Level		SU=[Param.]<CR><LF>	0=low	255=high	Range 0 to 255
WC		White clip Level		WC=[Param.]<CR><LF>	0=low	255=high	Range 0 to 255
GS		Gamma Select		GS=[Param.]<CR><LF>	0=gamma 1	1=gamma 0.45
	E – Saving and loading data in EEPROM
LD		Load settings from		LD=[Param.]<CR><LF>	0=Factory data	1=User 1 area	Latest used data
		camera EEPROM			2=User 2 area	3=User 3 area	area becomes
							default at next
							power up
SA		Save settings to		SA=[Param.]<CR><LF>	1=User 1 area	2=User 2 area
		camera EEPROM			3=User 3 area

*1) In normal non trigger mode (TR=0) PE<312 for CCIR and PE<262 for EIA. In trigger mode TR=1, EEN will not be correct if PE>833.

*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored.

!!Do not try to use commands not shown in the list.

- 19 -