JAI CV-M91 operation manual Other Functions

Page 18

CV-M91

6.3. Other Functions.

Refer to “7. Configuring the Camera.”

Scanning: SW1-5 on rear selects interlaced or non-interlaced. Non-interlaced PAL = 312H in EVEN field. Non-interlaced NTSC = 262 H in ODD field.

Gamma: SW1-6 on rear for gamma select. Gamma = 1 or gamma =0.45.

Gain: SW1-7 on rear select manual gain or AGC. Manual gain is set by VR7 on PK8406. In AGC the gain is automatic. The AGC level is set by potentiometer VR3.

Control: SW1-8 on rear selects the camera control mode. Either local by switches, or remote by “Camera Control Tool” via RS-232C. (Should be in position before power on.)

HD/VD in/out:

Jumper JP305 and JP306 on PK8407 are for switching between VD in/VD out. Jumper JP308 and JP309 on PK8407 are for switching between HD in/HD out

75 Ohm termination:

SW301 on PK8407 can terminate signal inputs from TTL to 75 Ω.

SW301-1 for HD. SW301-2 for VD. SW301-3 for ext. trigger. (On for 75Ω.)

VD/VS in: Jumper JP312, JP313, JP315, JP318 and JP319 on PK8407 select ext. HD/VD in or composite signal to the sync separator, which separate HV/VD.

Sync/WEN: Jumper JP303 and JP304 on PK8407 for Sync or WEN out on pin #7 on 9 pin sub-D.

Sync on green:

SW604 on PK8404 to ON for composite sync signal on green video output.

Pixel clock out:

Jumper JP301 on PK8407 short for pixel clock out on pin #9 on 12-pin connector.

Frame/field accumulation:

SW301-4 on PK8407 for frame or field accumulation.

CCD iris: SW201 on PK8408 to ON for CCD iris function in the regulation. The reference level can be set by potentiometer VR10 on PK8406.

One Push White Balance:

SW202 on PK8408 switch between manual and one push white balance. Manual allows the white balance to be set by R and B potentiometer on rear. One push is done automatic if switch on camera rear is pressed.

Red and Blue gain setting:

R and B gain potentiometer on camera rear is for manual white adjust.

Manual gain:

VR7 on PK8406 is for manual gain setting. *)

CCD iris setting:

VR10 potentiometer on PK8406 is for CCD iris reference level. *)

AGC setting:

VR3 potentiometer on PK8406 is for AGC reference level. *)

The following functions are for RS 232C control only.

Red, Green and Blue gain level. *)

Red, Green and Blue white clip level. *)

Red, Green and Blue offset level. *)

*) Do not adjust these settings unless you are familiar with color camera adjustments.

- 17 -

Page 17 Page 19
Image 18
Page 17 Page 19
Contents CV-M91 Table of Contents CV-M91Main Features GeneralStandard Composition Locations and Functions LocationsPin no Signal Remarks Pin Multi-connector DC-IN/TriggerPin Multi-connector Trigger and RS232C Pin AssignmentPin no Pin Sub D-connector VideoInput and Output Circuits Video outputsPrism unit HD, VD, WEN, EEN and Pclk outputInput/Output of Signals Functions and OperationsInput/output of HD/VD VBS out on pin#4 12 pin Internal sync out/WEN outInternal pixel clock out Out/VBS out on pin#6 9 pin sub-DTrigger Modes Long time integrationContinuous Operation Non triggered PAL horizontal timingVertical timing PAL interlaced Vertical timing Ntsc interlaced Edge Pre-select Mode Vertical timing for edge pre-select PALPulse Width Control Mode Vertical timing for pulse width control PALStart Stop Mode Start stop interlaced field integrationLong time integration Long time interlaced field integrationOther Functions Switch settings inside Configuring the CameraSwitch settings 1. SW1 on rear panelJumper settings inside ShortSwitch and jumper positions Board positionsCV-M91command list RS-232C controlCamera Control Tool for CV-M91 Window from camera control toolExternal Appearance and Dimensions SpecificationsSpectral sensitivity Specification table CV-M91PCV-M91 Opto-mechanical specifications Opto mechanical specificationsPrecautions Typical CCD CharacteristicsAppendix Users Mode Settings Users Modifications Users RecordCamera type CV-M91 Revision Revision a Serial No ……………
Top Page Image Contents