JAI CV-M91 Configuring the Camera, 1. SW1 on rear panel, Switch settings inside

Page 19

CV-M91

7. Configuring the Camera

7.1 Switch settings

The switch positions are shown in factory setting. Names in bold italic is factory setting.

7.1.1. SW1 on rear panel

SW 1 on rear

OFF				ON
				1
SHUTTER				2
				3
TRIGGER				4
TRIGGER				4
INTERLACE				5
GAMMA				6
GAMMA				6
GAIN				7
CONTROL				8

1/60 1/125

1/250

1/500

1/1000

1/2000

1/4000

1/10,000

second

<< < < > > > >

<< > > < < > >

<> < > < > < >

Normal	<	>	Random
Intel.	<	>	.
Intel.	<	>	Non-interl.
Gam. 1	<	>	Gam. 0.45
Man.	<	>	AGC
Local	<	>	RS-232C

Note:

SW1-1 through 3 OFF:

In Normal mode: The shutter is OFF

In Trigger mode: 1/50 for PAL. 1/60 for NTSC

SW1-1 through 2 OFF. SW1-3 ON:

In Normal mode: 1/100

In Trigger mode: 1/125

Fig. 30. Mode switch on camera rear

7.1.2. Switch settings inside

SW 604 on PK 8404

On pin #4 12P	VBS out
On pin #6 9P	Y/VBS out
On pin #4. 9P	Sync on G

ON			OFF
		1				VBS	<	>	NC
		2					> <		Y - VBS
		3					<	>	Y - VBS
		3					<	>
		4				G+S	<	>	G

Fig. 31. Switch on PK8404 for video output.

SW 301 on PK 8407

OFF				ON
HD term.				1
VD term.				2
Trig term.				3
Accumul.				4

TTL < > 75 Ohm TTL < > 75 Ohm

TTL < > 75 Ohm field < > frame

Fig. 32. Switch on PK8407 for 75Ω termination and accumulation.

SW 201 on PK 8408

OFF				ON
CCD iris				1

Off < > CCD iris on

Fig. 33. Switch on PK8408 for CCD iris.

SW 202 on PK 8408

OFF ON

White bal. 1

Man. < > One push

Fig. 34. Switch on PK8404 for white balance.

- 18 -

Image 19

Contents CV-M91 CV-M91 Table of ContentsGeneral Main FeaturesStandard Composition Locations Locations and FunctionsPin Assignment Pin Multi-connector DC-IN/TriggerPin Multi-connector Trigger and RS232C Pin no Signal RemarksVideo outputs Pin Sub D-connector VideoInput and Output Circuits Pin noHD, VD, WEN, EEN and Pclk output Prism unitFunctions and Operations Input/Output of SignalsInput/output of HD/VD Out/VBS out on pin#6 9 pin sub-D Internal sync out/WEN outInternal pixel clock out VBS out on pin#4 12 pinLong time integration Trigger ModesPAL horizontal timing Continuous Operation Non triggeredVertical timing PAL interlaced Vertical timing Ntsc interlaced Vertical timing for edge pre-select PAL Edge Pre-select ModeVertical timing for pulse width control PAL Pulse Width Control ModeStart stop interlaced field integration Start Stop ModeLong time interlaced field integration Long time integrationOther Functions 1. SW1 on rear panel Configuring the CameraSwitch settings Switch settings insideShort Jumper settings insideBoard positions Switch and jumper positionsRS-232C control CV-M91command listWindow from camera control tool Camera Control Tool for CV-M91Specifications External Appearance and DimensionsSpectral sensitivity CV-M91P Specification tableOpto mechanical specifications CV-M91 Opto-mechanical specificationsTypical CCD Characteristics PrecautionsAppendix Users Record Users Mode Settings Users ModificationsCamera type CV-M91 Revision Revision a Serial No ……………