JAI CV-M91 Internal sync out/WEN out, Internal pixel clock out, VBS out on pin#4 12 pin

Page 9

CV-M91

6.1.2. Internal sync out/WEN out

On pin #7 on 9 pin sub-D connector, the factory setting is the internal composite sync signal out. By jumper settings it can be changed to WEN out.

Refer to “7. Configuring the Camera.”

To use this mode:

Set function on PK8407: JP303 o, JP304 s for sync output. Factory default. JP303 s, JP304 o for WEN output.

6.1.3. Internal pixel clock out

The internal pixel clock can be output on pin #9 on the 12 pin connector. As factory setting it is not connected.

Refer to “7. Configuring the Camera.”

To use this mode:

Set function on PK8407: JP310 o, for no pixel clock out. Factory default. JP310 s, for pixel clock out.

Important notes on using this mode.

If not used, the pixel clock should not be output.

6.1.4. VBS out on pin#4 12 pin.

On pin #4 on the 12 pin connector, the video signal can be output as a composite signal. Refer to “7. Configuring the Camera.”

To use this mode:

Set function on PK8404: SW604-1 on for VBS video signal out on pin #4 12 pin. Factory default. SW604-1 off for no signal out on pin #4 12 pin.

6.1.5. Y out/VBS out on pin#6 9 pin sub-D.

The signal output on pin #6 on the 9 pin sub.D connector can be changed from Y output to composite video output.

Refer to “7. Configuring the Camera.”

To use this mode:

Set function on PK8404: SW604-2 off, SW604-3 on for Y out on pin #6 9 pin. Factory default. SW604-2 on, SW604-3 off for VBS out on pin #6 9 pin.

6.1.6. Green out/sync on green on pin#4 9 pin sub-D.

The green signal output on pin #4 9 pin sub-D can be changed to be composite sync on green. Refer to “7. Configuring the Camera.”

To use this mode:

Set function on PK8404: SW604-4 off for green video out on pin #4 9 pin. Factory default. SW604-4 on for sync on green out on pin #4 9 pin.

- 8 -

Image 9
Contents CV-M91 CV-M91 Table of ContentsMain Features GeneralStandard Composition Locations Locations and FunctionsPin Multi-connector Trigger and RS232C Pin Multi-connector DC-IN/TriggerPin no Signal Remarks Pin AssignmentInput and Output Circuits Pin Sub D-connector VideoPin no Video outputsHD, VD, WEN, EEN and Pclk output Prism unitInput/Output of Signals Functions and OperationsInput/output of HD/VD Internal pixel clock out Internal sync out/WEN outVBS out on pin#4 12 pin Out/VBS out on pin#6 9 pin sub-DLong time integration Trigger ModesPAL horizontal timing Continuous Operation Non triggeredVertical timing PAL interlaced Vertical timing Ntsc interlaced Vertical timing for edge pre-select PAL Edge Pre-select ModeVertical timing for pulse width control PAL Pulse Width Control ModeStart stop interlaced field integration Start Stop ModeLong time interlaced field integration Long time integrationOther Functions Switch settings Configuring the CameraSwitch settings inside 1. SW1 on rear panelShort Jumper settings insideBoard positions Switch and jumper positionsRS-232C control CV-M91command listWindow from camera control tool Camera Control Tool for CV-M91External Appearance and Dimensions SpecificationsSpectral sensitivity CV-M91P Specification tableOpto mechanical specifications CV-M91 Opto-mechanical specificationsPrecautions Typical CCD CharacteristicsAppendix Users Mode Settings Users Modifications Users RecordCamera type CV-M91 Revision Revision a Serial No ……………