JAI operation manual Specification table, CV-M91P

Page 25

CV-M91

9.2. Specification table

Specifications	CV-M91P			CV-M91N
Scanning system	CCIR PAL, 25 frames/sec.			EIA NTSC. 30 frames/sec.
	625 lines, 2:1 Interlaced			525 lines, 2:1 Interlaced
Frame rate	50 Hz			59.94 Hz
Line frequency	15.625 kHz			15.734 kHz
Pixel frequency	14.25 MHz			14.349949 MHz
CCD sensors	3 x 1/3” monochrome IT CCD			3 x 1/3” monochrome IT CCD
	ICX-409AL-6			ICX-408AL-6
Sensing area		4.8 (h) x	3.6 (v) mm
Effective pixels	752 (h) x 582 (v)			768 (h) x 494 (v)
Pixels in video output	744 (h) x 575 (v)			765 (h) x 486 (v)
Cell size	6.5 (h) x 6.25 (v) ∝m			6.35 (h) x 7.4 (v) ∝m
Resolution horizontal		570 TV lines
Sensitivity (on sensor)	0.5 Lux, Max gain, 50% video
S/N ratio	54 dB			56 dB
Video outputs. (DC coupled)	RGB			RGB
	Y/C PAL			Y/C NTSC
	VBS PAL			VBS NTSC
Video output level	RGB and C signal, 0.7 Vpp, 75 Ω
	G on sync, Y signal and Composite VS, 1.0 Vpp, 75 Ω
Gamma		1.0 - 0.45
Gain		Manual – Automatic
Gain range		0 to +18 dB
Accumulation		Field – Frame
Synchronization	Int. X-tal. Ext HD/VD or random trigger
Scanning	2:1 interlaced, non-interlaced
Composite VS input	1.0 Vpp ±0.3V. 75 Ω terminated
Composite sync output		4 Vpp from 75 Ω source
HD/VD sync input	4 Vpp	±2 V. (Termination TTL or 75 Ω)
HD/VD sync output		4 Vpp from 75 Ω source
Trigger input	4 Vpp	±2 V. (Termination TTL or 75 Ω)
WEN output (write enable)		4 Vpp from 75 Ω source
EEN output (exposure enable)		4 Vpp from 75 Ω source
Pixel clock output		4 Vpp from 75 Ω source
Shutter.
Continuous and Edge pre-select	(off), 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10,000 sec.
Pulse width control input		1 H to 900 H
Start/stop		1/10,000 to 1/77 second
Long time exposure		1 field to ∞
White balance	Manual, one push (2350 to 6400 K)
Functions controlled by	Trigger mode, Shutter speed, Accumulation, Interlace, AGC level, White clip,
RS 232C	Set-up, Manual gain, AGC/manual gain, Internal/ potentiometer gain set,
		Gamma, white balance.
Functions controlled by internal DIP	VD input/output, HD input/output
switches	HD, VD and Trigger 75 Ω termination on/off
Operating temperature		-5°C to +45°C.
Humidity		20 - 80% non-condensing
Storage temp./humidity	-25°C to 60°C./20% - 90 % non-condensing
Vibration		3 G (15 Hz – 200 Hz in XYZ)
Shock		50 G
Regulations	CE (EN 50081-1, EN 50082-1) FCC part 15
Power		12V DC ± 10%. 6 W
Lens mount	C-mount. (Max 4.0 mm thread)
Dimensions		50 x 60 x 130 mm		(HxWxD)
Weight		480 g

- 24 -

Image 25

Contents CV-M91 CV-M91 Table of ContentsGeneral Main FeaturesStandard Composition Locations Locations and FunctionsPin Multi-connector Trigger and RS232C Pin Multi-connector DC-IN/TriggerPin no Signal Remarks Pin AssignmentInput and Output Circuits Pin Sub D-connector VideoPin no Video outputsHD, VD, WEN, EEN and Pclk output Prism unitFunctions and Operations Input/Output of SignalsInput/output of HD/VD Internal pixel clock out Internal sync out/WEN outVBS out on pin#4 12 pin Out/VBS out on pin#6 9 pin sub-DLong time integration Trigger ModesPAL horizontal timing Continuous Operation Non triggeredVertical timing PAL interlaced Vertical timing Ntsc interlaced Vertical timing for edge pre-select PAL Edge Pre-select ModeVertical timing for pulse width control PAL Pulse Width Control ModeStart stop interlaced field integration Start Stop ModeLong time interlaced field integration Long time integrationOther Functions Switch settings Configuring the CameraSwitch settings inside 1. SW1 on rear panelShort Jumper settings insideBoard positions Switch and jumper positionsRS-232C control CV-M91command listWindow from camera control tool Camera Control Tool for CV-M91Specifications External Appearance and DimensionsSpectral sensitivity CV-M91P Specification tableOpto mechanical specifications CV-M91 Opto-mechanical specificationsTypical CCD Characteristics PrecautionsAppendix Users Record Users Mode Settings Users ModificationsCamera type CV-M91 Revision Revision a Serial No ……………