Kodak 4F3882 manual How it Works, Calibration, Characterization

Page 13

I n t r o d u c t i o n

How it Works

To accurately generate a LUT, you must work from a calibrated and characterized display. A sensor, which you position on your display, measures the luminance and chromaticities of a series of color patches. You can also use the sensor to verify the calibration and characterization.

NOTE

To characterize a projector you must use a spectrophotometer or a colorimeter suitable for measuring screen reflectance.

Calibration

The automatic calibration process gathers information from a sensor and transfers it to the monitor via the enable cable (USB Cable ECC 1). Adjustments are automatically made to the monitor contrast, brightness, and individual RGB biases and gains via the enable cable, based on information gathered by the sensor.

The first time that you initiate automatic calibration, the system prompts you to perform a monitor evaluation to determine if your monitor is capable of being automatically calibrated.

When calibrating an HD/SD device, you must manually calibrate the device using standard SMPTE procedures. A colorbars target is supplied with the Display Manager System.

Manually calibrate your display to SMPTE standards if:

•You are using an IRIX system

•You have an HD/SD device

•The enable cable does not recognize your monitor

•You were unable to successfully calibrate your monitor using automatic calibration

Characterization

After you have calibrated your display, you must characterize it to determine the gamma response and to track the primaries. The result is a .chr file, which the system uses to create a LUT.

HD/SD displays and digital projectors must be characterized using the Manual Characterization Assistant. When characterizing these displays, you can:

•project display patches (provided on the Display Manager System CD or downloaded from http://www.kodak.com/US/en/motion/products/ dlmanage/kdmDown.jhtml) through a supported imaging application

•display patches from one of the KODAK Color Patch Set video tapes available from Kodak

K O D A K D i s p l a y M a n a g e r S y s t e m V 4 . 1 U s e r ’ s G u i d e

3

Image 13

Contents Display Manager system User guide Page Display Manager System USER’S Guide Page AB O U T T H I S BO O K Page TA B L E O F CO N T E N T S Calibration Verifying Appendix C Regulatory Information T RO D U C T I O N Print Film Edition VISION2 HD System Types of LicensesCalibration How it WorksCharacterization Verification Viewing and Customizing a LookMain Window Supported Hardware Enable Cable USB Cable ECCGeneric Monitor Support Supported DisplaysWindows MAC OS Irix OS Linux OS Supported SensorsGetting Help Windows and Macintosh Operating System Installation Install the SoftwareTo install on a Windows or Macintosh Operating System To install on an Irix system Irix InstallationGunzip KDMV4Irix.tar.gz Tar xf KDMV4Irix.tar To install on a Linux system Linux InstallationConnect the Hardware Rite Sensors To connect the enable cableTo position the sensor during calibration Rite Monitor Optimizer DTP92+EK To connect the sensor Do not apply a cleanser to the suction cupSequel Chroma 4/C USB Sensor for CRT Monitors Sequel SensorsSequel Chroma 4/L USB Sensor Sequel Chroma 4/C Serial Sensor for CRT Monitors Click Type and select PhotoResearch PR-650 Go to Options SetupClick Type and select Minolta CS-100A To purchase a license Obtain Your LicenseManager System/Licenses Renewing Your License Open the Display Manager SystemPage Preparing the Viewing Environment and Monitor Be FO R E CA L I B R a T I N GSetting the Options Projector Aim Print Film Calibration SetupDisplay Automatic Calibration Display AimAim Settings Video Calibration SetupWhite Patch Dark PatchTolerances Setup Sensor SetupDisplay Setup Use Video Calibration SettingsDirectories Setup Timing SetupTo load a customized .ini file Go to File Load Settings Saving and Loading SettingsTo save all settings at once Go to File Save Settings To create a customized .ini fileAutomatic Calibration CA L I B R a T I O NTo automatically calibrate a monitor Calibration ProcedureIf you are prompted to perform a Dark Gain Correction L i b r a t i o n L i b r a t i o n To evaluate your monitor Monitor EvaluationTo manually calibrate a monitor or HD/SD display Manual CalibrationL i b r a t i o n Click Measure Once or Measure Continuous Click Measure PrimariesProceed to Characterization on Page Automatic Characterization CH a R a C T E R I Z a T I O NTo automatically characterize your monitor A r a c t e r i z a t i o n If characterization failed, see Characterization Failure on Manual Characterization To manually characterize When you are finished, click File Save Characterization File Editing a Characterization Table Task Shortcut Keys for the AssistantOpening the Viewer VI E W I N G a N D CU S T O M I Z I N G LO O K STo open the Viewer Global Options Using the ViewerTo Quick Verify Chart with the results is displayed E w i n g a n d C u s t o m i z i n g L o o k s Playback Controls Pop-up Options Toolbar InformationTask Key Viewer Shortcut KeysTo create a print film look Creating a Print Film LookTo create a video look Creating a Video LookLoading an Image Advanced Options Framing SettingsMode Description Gamut Remap SettingsTransform Bit Depth Work in a dark environment whenever possible Surround CompensationExample file neutral-based compensation Recorder CompensationOn the Advanced tab, click Recorder Compensation Example file neutral- and color-based compensationTransform Rescale Page To verify monitor setup Verifying the Monitor SetupVE R I F Y I N G Verification window opens when the correction is complete Data verify To verify the print film look Verifying the Print Film LookVerification window opens when the correction is complete Ve r i f y i n g Verification Logs VerifySetupResults or VerifyPrintFilmResultsMonitor Setup Verification Log TRO U B L E S H O O T I N G Calibration Failure Verification Failure Characterization FailureDark Gain Correction Failure Sensor Needs to be Replaced Sensor Does Not Adhere to ScreenUSB Device Is Not Recognized Sensor Fails to InitializeLicense Has Expired Enable Cable Does Not Recognize the MonitorLicense File Does Not Work Unable to Load a Transform Unable to Load an ImageUnable to Build or Export a Transform Calibrate Icon Is Not AvailableImaging Product Cannot Find LUT Problem with the .ini FileMy 1D LUT Does Not Match my 3D LUT My Wide Color Gamut Encoded LUT Does Not Look CorrectImage Does Not Appear in the Viewer Click the Troubleshooting tabTr o u b l e s h o o t i n g Results Are Not as Expected Difficulty Navigating the Online User’s Guide Super Bright Capable Display will not CalibrateHot Links Paging Through the User’s Guide Windows Operating System Minimum Requirements AP P E N D I X a SY S T E M RE Q U I R E M E N T SMAC OS Minimum Requirements Linux Operating System Minimum Requirements Irix Operating System Minimum RequirementsAdditional Software and Hardware Page Display Manager System Shortcut Keys AP P E N D I X B SH O R T C U T KEY SManual Characterization Assistant Shortcut Keys Viewer Shortcut Keys AP P E N D I X C RE G U L a T O R Y in FO R M a T I O N EU Weee GL O S S a R Y Options Setup window TemperatureDisplay mode Enable cableSPD See projector SPD AssistantVISION2 HD System See Kodak VISION2 HD System D EX D e Macintosh Rite Page Eastman Kodak Company