Philips KX-HCM8 operating instructions Isp, Network window on

Page 107

	Operating Instructions
	About Network Camera Setup

Problem	Cause and Remedy

Power Indicator	• Internal Failure of the server or the congestion on the network
continues	traffic when using DHCP may prevent Network Camera from
blinking.	getting the IP address. Ask the network administrator or your
	ISP.
	• Power Indicator blinks when updating firmware on page 82.
	When the Update Firmware failed, refer to page 108.
	• If you cannot access Network Camera, the Network Camera
	hardware may be defective. Call our customer call center.

Image Transfer	• Default Gateway and DNS server address should be set up on
on e-mail or FTP	Network window on page 50.
does not work.	• If FTP does not work properly, ask your ISP or network
	• If FTP does not work properly, ask your ISP or network
	administrator about the transferring mode of FTP server.
	[Passive Mode] or [Active Mode] is available.
	• Select [One Time] for Login Timing when transferring images
	by FTP in short duration time.

Timer mode	Short interval of Image Buffer Frequency makes Network Camera
transfers older	transfer the older images. Set the interval long enough to transfer
images.	the images. Buffered Image screen enables you to check this
	setting.

[For assistance, please call: 1-800-272-7033]

107

Image 107

Contents Network Camera For operation assistance Call IntroductionNetwork Camera Memo TrademarksImportant Safety Instructions Table of Contents Index 115 Specification and TroubleshootingTechnical Guides Section Getting to Know Network Camera Main FeaturesMulti-Language Display Update FirmwareAuthentication System Requirements Authentication window Authentication-System Security FeatureIncluded Accessories Setup CD-ROM Front View Camera Feature LocationsBottom View Rear ViewNetwork Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeType 4-Direct Connection with a PC Type 3-Internet Direct Connection with a ModemHow to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera IP address Network Camera Configuration Type Port NoDefault Network Parameters TableEnter winipcfg and click OK. IP configuration window appears How to refer the network parameters from the PCSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the InternetIf Top Page does not appear TopOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Help Motion JpegSingle Camera Multi-CameraActiveX Controls Single Camera Screen Using Operation Bar Viewing Buffered Image Screen Non Transfer mode Alarm/Timer modeSecondary ViewerClicking Start Capture PrimaryMulti-Camera Screen Setup Setup Name/Time AdministratorCamera Setup Go to TopFunctions of Network Camera Entered. If any operational issues are changed, tryThis option first. Refer to Go to Top Network Enter only the number Instructions for the data fieldsDhcp File size of the image DdnsDate Name/TimeCamera NameTime Zone AdjustmentTime Changed AM/PM or 24H AutoClick Security Administrator on Setup Security AdministratorRetype EnableFor Setup Password Security General User Click Security General User on SetupNew User User ID ListDelete or Modify Top View Image 160 x Image Quality ResolutionInstructions for the data fields Top ImageImage Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm ModeActive Time of Trigger Alarm enable conditionSets the image resolution and image quality Login timing Data transfer method Over write settingSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Fixed Power LineWhite Balance Fixed IndoorMulti-Camera Camera Name Enable check boxIP Address or URL * 1 or HostExternal Output Control Click External Output Control on SetupIndicator Control Status Click Restart Now RestartUpdate Firmware Click Update Firmware Operating Instructions Click Reset to Factory Default on Setup Click Execute Reset to Factory DefaultTechnical Guides Tripod Mounting MountingFlexible Stand Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top External Sensor Input Interfacing to the External I/OExplanation of External I/O Pin FunctionCircuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Items Factory Default Indispensable setting Value Network Default Settings ListImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Other Specification Description SpecificationsNetwork Camera Specifications Description SMTP, FTP Problem Cause and Remedy TroubleshootingAbout Network Camera Setup For Indicator Control window Network window on ISPAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen About Other Troubles View Image Setting window onConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP When you ship the product For product service