Philips KX-HCM8 operating instructions For product service, When you ship the product

Page 118

For product service

Panasonic Servicenters are listed in the servicenter directory.

Call 1-800-272-7033 for the location of an authorized servicenter.

After the limited warranty, please contact our Continued Services Technical Support Line at 1-900-555-PANA (1-900-555-7262). If you have difficulty reaching this number, it may be blocked by your phone company. Please contact your local phone company to correct this.

This Network Camera is designed for use in the United States of America. Sale or use of this product in other countries/areas may violate local laws.

When you ship the product

Carefully pack your unit, preferably in the original carton.

Attach a letter, detailing the symptom, to the outside of the carton.

Symptom

Send the unit to an authorized servicenter, prepaid and adequately insured.

Do not send your unit to the Panasonic Consumer Electronics Company listed below or to executive or regional sales offices. These locations do not repair consumer products.

Operating Instructions are subject to change without notice.

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation of America

Panasonic Sales Company,

Division of Matsushita Electric of Puerto Rico, Inc.

Copyright:

This manual is copyrighted by Panasonic Communications Co., Ltd. (PCC). Under the applicable copyright laws, this manual may not be reproduced in any form, in whole or part, without the prior written consent of PCC and its licensee.

2001 Panasonic Communications Co., Ltd. All Rights Reserved.

Printed in Japan

PSQX2679YA KK1101RM1013

Image 118

Contents Network Camera Introduction For operation assistance CallTrademarks Network Camera MemoImportant Safety Instructions Table of Contents Technical Guides Specification and TroubleshootingIndex 115 Section Main Features Getting to Know Network CameraAuthentication Update FirmwareMulti-Language Display System Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM Camera Feature Locations Front ViewRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband RouterType 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCHow to turn on Network Camera for Installation Preparing the Network Parameters for Network Camera Network ParametersNetwork parameters memo for Network Camera Network Parameters Table Network Camera Configuration Type Port NoDefault IP addressHow to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appearsSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop If Top Page does not appearOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Example TopHttp//Global IP address of Broadband RouterPortNo Top Multi-Camera Motion JpegSingle Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenPrimary ViewerClicking Start Capture SecondaryMulti-Camera Screen Setup Setup Go to Top AdministratorCamera Setup Name/TimeThis option first. Refer to Entered. If any operational issues are changed, tryFunctions of Network Camera Go to Top Network Instructions for the data fields Enter only the numberDhcp Ddns File size of the imageName Name/TimeCamera DateAuto AdjustmentTime Changed AM/PM or 24H Time ZoneSecurity Administrator Click Security Administrator on SetupFor Setup Password EnableRetype Click Security General User on Setup Security General UserDelete or Modify User ID ListNew User Top View Image Image ResolutionInstructions for the data fields Top 160 x Image QualityImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer windowSets the image resolution and image quality Alarm enable conditionActive Time of Trigger Login timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Fixed Indoor Power LineWhite Balance FixedMulti-Camera URL * 1 or Host Enable check boxIP Address or Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Restart Click Restart NowUpdate Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click ExecuteTechnical Guides Flexible Stand Mounting MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value NetworkImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Network Camera Specifications Description SpecificationsOther Specification Description SMTP, FTP About Network Camera Setup TroubleshootingProblem Cause and Remedy For Indicator Control window ISP Network window onAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product