Philips KX-HCM8 operating instructions Click External Output Control on Setup

Page 78

Operating Instructions

3.5.10External Output Control

External Output Control window enables the External Device Control Output signal to activate the external sensors/devices. (Open or Short to GND) The network administrator should set up this setting.

1.

2.

3.

Note

Refer to page 91 for Interfacing to the External I/O.

Click [External Output Control] on Setup Page.

Check [Open] means the External Device Control Output becomes high impedance (open collector).

Check [Short to GND] means the External Device Control Output becomes low (0V).

Click [Save] to send the signal.

•Click [Cancel] to quit the current settings. The window returns to Setup Page without saving the parameters.

78

Image 78

Contents Network Camera Introduction For operation assistance CallTrademarks Network Camera MemoImportant Safety Instructions Table of Contents Specification and Troubleshooting Technical GuidesIndex 115 Section Main Features Getting to Know Network CameraUpdate Firmware AuthenticationMulti-Language Display System Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM Camera Feature Locations Front ViewRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband RouterType 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCHow to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Network Parameters Table Network Camera Configuration Type Port NoDefault IP addressHow to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appearsSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop If Top Page does not appearOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Multi-Camera Motion JpegSingle Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenPrimary ViewerClicking Start Capture SecondaryMulti-Camera Screen Setup Setup Go to Top AdministratorCamera Setup Name/TimeEntered. If any operational issues are changed, try This option first. Refer toFunctions of Network Camera Go to Top Network Instructions for the data fields Enter only the numberDhcp Ddns File size of the imageName Name/TimeCamera DateAuto AdjustmentTime Changed AM/PM or 24H Time ZoneSecurity Administrator Click Security Administrator on SetupEnable For Setup PasswordRetype Click Security General User on Setup Security General UserUser ID List Delete or ModifyNew User Top View Image Image ResolutionInstructions for the data fields Top 160 x Image QualityImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer windowAlarm enable condition Sets the image resolution and image qualityActive Time of Trigger Login timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Fixed Indoor Power LineWhite Balance FixedMulti-Camera URL * 1 or Host Enable check boxIP Address or Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Restart Click Restart NowUpdate Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click ExecuteTechnical Guides Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value NetworkImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Specifications Network Camera Specifications DescriptionOther Specification Description SMTP, FTP Troubleshooting About Network Camera SetupProblem Cause and Remedy For Indicator Control window ISP Network window onAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product