Philips KX-HCM8 operating instructions Camera Feature Locations, Front View

Page 14

Operating Instructions

1.3Camera Feature Locations

1.3.1Front View

Power Indicator

(Refer to page 79 for the setup.)

Fixed Focus Lens

1 m (40 inches) – Infinity

Attachment Lens (30.5 mm)

(customer provided)

Turn the attachment lens till it stops.

Power Indicator

Power Indicator can be controlled on Indicator Control window on page 79. Power Indicator blinks in the following situations.

•During the Update Firmware.

•During initializing after pushing CLEAR SETTING button.

•During getting the IP address from the DHCP server.

•Because of the internal failure of Network Camera. Refer to page 107.

Fixed Focus Lens

Network Camera uses Fixed Focus Lens. Minimum distance between Network Camera and object is 1 meter (40 inches).

Note

Do not touch the Fixed Focus Lens. Touching it may leave a fingerprint and can cause the image to be out of focus. This can also remove the protective coating from the Fixed Focus Lens.

Corresponding to the attachment lens (customer provided)

The Network Camera’s lens is threaded to accept optional diopter lens (customer provided), similar to those used with camcorders. Panasonic does not offer any at this time. If the lens you choose is slightly larger than 30.5 mm, adaptor rings can be purchased from most photographic supply dealers. The adaptor should be selected to convert 30.5 mm to the diameter of the lens you choose.

14

Image 14

Contents Network Camera Introduction For operation assistance CallTrademarks Network Camera MemoImportant Safety Instructions Table of Contents Index 115 Specification and TroubleshootingTechnical Guides Section Main Features Getting to Know Network CameraMulti-Language Display Update FirmwareAuthentication System Requirements Authentication-System Security Feature Authentication windowIncluded Accessories Setup CD-ROM Camera Feature Locations Front ViewRear View Bottom ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Type 2-Internet Connection with a Broadband RouterType 3-Internet Direct Connection with a Modem Type 4-Direct Connection with a PCHow to turn on Network Camera for Installation Network parameters memo for Network Camera Network ParametersPreparing the Network Parameters for Network Camera Network Parameters Table Network Camera Configuration Type Port NoDefault IP addressHow to refer the network parameters from the PC Enter winipcfg and click OK. IP configuration window appearsSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Network Camera Access from the Internet Port Forwarding IP Masquerade featureTop If Top Page does not appearOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Http//Global IP address of Broadband RouterPortNo Top TopExample Multi-Camera Motion JpegSingle Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Non Transfer mode Alarm/Timer mode Viewing Buffered Image ScreenPrimary ViewerClicking Start Capture SecondaryMulti-Camera Screen Setup Setup Go to Top AdministratorCamera Setup Name/TimeFunctions of Network Camera Entered. If any operational issues are changed, tryThis option first. Refer to Go to Top Network Instructions for the data fields Enter only the numberDhcp Ddns File size of the imageName Name/TimeCamera DateAuto AdjustmentTime Changed AM/PM or 24H Time ZoneSecurity Administrator Click Security Administrator on SetupRetype EnableFor Setup Password Click Security General User on Setup Security General UserNew User User ID ListDelete or Modify Top View Image Image ResolutionInstructions for the data fields Top 160 x Image QualityImage Transfer Non Transfer mode Transfer in the Alarm Mode Click Alarm on Image Transfer windowActive Time of Trigger Alarm enable conditionSets the image resolution and image quality Login timing Over write setting Data transfer methodSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup Fixed Indoor Power LineWhite Balance FixedMulti-Camera URL * 1 or Host Enable check boxIP Address or Camera NameClick External Output Control on Setup External Output ControlIndicator Control Status Restart Click Restart NowUpdate Firmware Click Update Firmware Operating Instructions Reset to Factory Default Click Reset to Factory Default on Setup Click ExecuteTechnical Guides Tripod Mounting MountingFlexible Stand Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Pin Function Interfacing to the External I/OExplanation of External I/O External Sensor InputCircuit Diagram Example Ascii and ISO-8859-1 Character Table Unavailable character setDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Default Settings List Items Factory Default Indispensable setting Value NetworkImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Other Specification Description SpecificationsNetwork Camera Specifications Description SMTP, FTP Problem Cause and Remedy TroubleshootingAbout Network Camera Setup For Indicator Control window ISP Network window onAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen View Image Setting window on About Other TroublesConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP For product service When you ship the product