Philips KX-HCM8 operating instructions Preparing the Network Parameters for Network Camera

Page 21

Operating Instructions

2.4Network Parameters

2.4.1Preparing the Network Parameters for Network Camera

Before starting to set up the network parameters of Network Camera, make note of corresponding network parameters.

[Type 1] Ask your network administrator for the network parameters.

[Type 2] Refer to the broadband router’s manual for the network parameters.

[Type 3] Ask your ISP (Internet Service Provider) for the network parameters.

[Type 4] Install Network Camera in the default condition. Set the PC "192.168.0.250" (IP address) and "255.255.255.0" (Subnet Mask). Refer to page 24.

Refer to page 22 and page 23 for network parameters.

Network parameters memo for Network Camera

The devices on the network may not be assigned the same IP address. Each device must have its own IP address. Overlapped IP addresses can cause other network devices to stop working and may result in widespread network problems.

IP Address	.	.	.
Default Gateway	.	.	.

Subnet Mask	.	.		.
DNS Server 1		.	.	.

DNS Server 2

.

.

.

[For assistance, please call: 1-800-272-7033]

21

Image 21

Contents Network Camera For operation assistance Call IntroductionNetwork Camera Memo TrademarksImportant Safety Instructions Table of Contents Specification and Troubleshooting Technical GuidesIndex 115 Section Getting to Know Network Camera Main FeaturesUpdate Firmware AuthenticationMulti-Language Display System Requirements Authentication window Authentication-System Security FeatureIncluded Accessories Setup CD-ROM Front View Camera Feature LocationsBottom View Rear ViewNetwork Camera Setup Installation Procedure Type 2-Internet Connection with a Broadband Router Network Camera Configuration TypeType 4-Direct Connection with a PC Type 3-Internet Direct Connection with a ModemHow to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Default Network Camera Configuration Type Port NoNetwork Parameters Table IP addressEnter winipcfg and click OK. IP configuration window appears How to refer the network parameters from the PCSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Port Forwarding IP Masquerade feature Network Camera Access from the InternetIf Top Page does not appear TopOperating Instructions Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Single Camera Motion JpegMulti-Camera HelpActiveX Controls Single Camera Screen Using Operation Bar Viewing Buffered Image Screen Non Transfer mode Alarm/Timer modeClicking Start Capture ViewerPrimary SecondaryMulti-Camera Screen Setup Setup Camera Setup AdministratorGo to Top Name/TimeEntered. If any operational issues are changed, try This option first. Refer toFunctions of Network Camera Go to Top Network Enter only the number Instructions for the data fieldsDhcp File size of the image DdnsCamera Name/TimeName DateTime Changed AM/PM or 24H AdjustmentAuto Time ZoneClick Security Administrator on Setup Security AdministratorEnable For Setup PasswordRetype Security General User Click Security General User on SetupUser ID List Delete or ModifyNew User Top View Image Instructions for the data fields Top ResolutionImage 160 x Image QualityImage Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm ModeAlarm enable condition Sets the image resolution and image qualityActive Time of Trigger Login timing Data transfer method Over write settingSetting Example Setting explanation Transfer in the Timer Mode Buffers or transfers by the timer trigger Login timing Over write setting Camera Setup White Balance Power LineFixed Indoor FixedMulti-Camera IP Address or Enable check boxURL * 1 or Host Camera NameExternal Output Control Click External Output Control on SetupIndicator Control Status Click Restart Now RestartUpdate Firmware Click Update Firmware Operating Instructions Click Reset to Factory Default on Setup Click Execute Reset to Factory DefaultTechnical Guides Mounting Flexible Stand MountingTripod Mounting Wall Mounting Ceiling Mounting Power Indicator On the Stand On the wall On the ceiling Top Explanation of External I/O Interfacing to the External I/OPin Function External Sensor InputCircuit Diagram Example Unavailable character set Ascii and ISO-8859-1 Character TableDisplayable character set Maintenance Specification and Troubleshooting Network Camera Reset Procedure-Default Settings Items Factory Default Indispensable setting Value Network Default Settings ListImage Transfer 100 For assistance, please call 101 Items Factory Default Indispensable setting Value Camera Specifications Network Camera Specifications DescriptionOther Specification Description SMTP, FTP Troubleshooting About Network Camera SetupProblem Cause and Remedy For Indicator Control window Network window on ISPAbout Network Camera Setup Problem Cause and Remedy About Top View Image screen About Other Troubles View Image Setting window onConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information 114 Index Operating Instructions TCP/IP When you ship the product For product service