Transcend Information CF 266X ¾ Word 1 Default Number of Cylinders, ¾ Words 10-19 Serial Number

Page 59

TS2G~8GCF266

266X CompactFlash Card

¾Word 1: Default Number of Cylinders

This field contains the number of translated cylinders in the default translation mode. This value will be the same as the number of cylinders.

¾Word 3: Default Number of Heads

This field contains the number of translated heads in the default translation mode.

¾Word 6: Default Number of Sectors per Track

This field contains the number of sectors per track in the default translation mode.

¾Words 7-8: Number of Sectors per Card

This field contains the number of sectors per CompactFlash Storage Card. This double word value is also the first invalid address in LBA translation mode.

¾Words 10-19: Serial Number

This field contains the serial number for this CompactFlash Storage Card and is right justified and padded with spaces (20h).

¾Word 22: ECC Count

This field defines the number of ECC bytes used on each sector in the Read and Write Long commands. This value shall be set to 0004h.

¾Words 23-26: Firmware Revision

This field contains the revision of the firmware for this product.

¾Words 27-46: Model Number

This field contains the model number for this product and is left justified and padded with spaces (20h).

¾Word 47: Read/Write Multiple Sector Count

Bits 15-8 shall be the recommended value of 80h or the permitted value of 00h. Bits 7-0 of this word define the maximum number of sectors per block that the CompactFlash Storage Card supports for Read/Write Multiple commands.

¾Word 49: Capabilities Bit 13: Standby Timer

If bit 13 is set to 1 then the Standby timer is supported as defined by the IDLE command If bit 13 is set to 0 then the Standby timer operation is defined by the vendor.

Bit 11: IORDY Supported

If bit 11 is set to 1 then this CompactFlash Storage Card supports IORDY operation.

If bit 11 is set to 0 then this CompactFlash Storage Card may support IORDY operation. Bit 10: IORDY may be disabled

Bit 10 shall be set to 0, indicating that IORDY may not be disabled. Bit 9: LBA supported

Bit 9 shall be set to 1, indicating that this CompactFlash Storage Card supports LBA mode addressing. CF devices shall support LBA addressing.

Bit 8: DMA Supported If bit 8 is set to 1 then Read DMA and Write DMA commands are supported. Bit 8 shall be set to 0. Read/Write DMA commands are not currently permitted on CF cards.

¾PIO Data Transfer Cycle Timing Mode

The PIO transfer timing for each CompactFlash Storage Card falls into modes that have unique parametric timing specifications. The value returned in Bits 15-8 shall be 00h for mode 0, 01h for mode 1, or 02h for mode 2. Values 03h through FFh are reserved.

Transcend Information Inc.

59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents Description Placement FeaturesDimensions 266X CompactFlash CardTranscend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification „ Output Drive Type „ Output Drive Characteristics „ Signal Interface „ Additional Requirements for CF Advanced Timing Modes Table Typical Series Termination for Ultra DMA 266X CompactFlash Card„ Ultra DMA Electrical Requirements ¾ Series termination required for Ultra DMA operation¾ Ultra DMA Mode Cabling Requirement „ Attribute Memory Read Timing Specification TS2G~8GCF266 „ Common Memory Read Timing Specification „ Common Memory Write Timing Specification „ I/O Input Read Timing Specification TS2G~8GCF266 „ I/O Output Write Timing Specification TS2G~8GCF266 „ True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 Table Ultra DMA Data Burst Timing „ True IDE Ultra DMA Mode Read/Write Timing Specification266X CompactFlash Card TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 „ Multiple Function CF+ Cards Card Configuration„ Single Function CF+ Cards TS2G~8GCF266 Attribute Memory Function „ Attribute Memory FunctionTS2G~8GCF266 TS2G~8GCF266 „ Pin Replacement Register Base + 04h in Attribute Memory „ Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionTable Common Memory Function Common Memory Transfer FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding „ I/O Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding „ Contiguous I/O Mapped Addressing„ Memory Mapped Addressing „ True IDE Mode Addressing¾ Data Register Address 1F0h170hOffset 0,8,9 „ CF-ATA Registers¾ Drive/Head LBA 27-24 Register Address 1F6h176h Offset ¾ Sector Count Register Address 1F2h172h Offset¾ Sector Number LBA 7-0 Register Address 1F3h173h Offset ¾ Cylinder High LBA 23-16 Register Address 1F5h175h OffsetTS2G~8GCF266 ¾ Device Control Register Address 3F6h376h Offset Eh ¾ Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set „ Check Power Mode 98h or E5h „ Erase Sectors C0h „ Execute Drive Diagnostic 90h„ Format Track 50h „ Flush Cache E7h„ Identify Device Ech 266X CompactFlash Card ¾ Word 0 General Configuration ¾ Word 49 Capabilities Bit 13 Standby Timer ¾ Word 1 Default Number of Cylinders¾ Word 3 Default Number of Heads ¾ Word 6 Default Number of Sectors per Track¾ Current Number of Cylinders, Heads, Sectors/Track ¾ Multiple Sector Setting¾ Total Sectors Addressable in LBA Mode ¾ Translation Parameters Valid¾ Word 68 Minimum PIO transfer cycle time with Iordy ¾ Words 82-84 Features/command sets supported¾ Word 65 Minimum Multiword DMA transfer cycle time ¾ Recommended Multiword DMA transfer cycle time¾ Words 85-87 Features/command sets enabled ¾ Word 89 Time required for Security erase unit completion ¾ Word 88 Ultra DMA Modes Supported and SelectedAdditional Requirements for CF Advanced Timing Modes ¾ Word 91 Advanced power management level value¾ Word 160 Power Requirement Description ¾ Word 128 Security Status Bit 8 Security LevelTS2G~8GCF266 „ Idle 97h or E3h „ NOP 00h „ Idle Immediate 95h or E1h„ Initialize Drive Parameters 91h „ Read DMA C8h „ Read Long Sector 22h or 23h „ Read Buffer E4hTS2G~8GCF266 „ Recalibrate 1Xh „ Request Sense 03h „ Seek 7Xh „ Set Features EFh Feature Supported 266X CompactFlash Card Translate Sector Information „ Standby Immediate 94h or E0h „ Translate Sector 87h„ Wear Level F5h „ Write Buffer E8h „ Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 „ Error Posting TS2G~8GCF266
Top Page Image Contents