Transcend Information CF 266X dimensions ¾ Word 65 Minimum Multiword DMA transfer cycle time

Page 61

TS2G~8GCF266

266X CompactFlash Card

Of these bits, bits 7 through 2 are reserved. Bit 0, if set to one, indicates that the CompactFlash Storage Card supports PIO mode 3. Bit 1, if set to one, indicates that the CompactFlash StorageCard supports PIO mode 4.

Support for PIO modes 5 and above are specific to CompactFlash are reported in word 163.

¾Word 65: Minimum Multiword DMA transfer cycle time

Word 65 of the parameter information of the Identify Device command is defined as the minimum Multiword DMA transfer cycle time. This field defines, in nanoseconds, the minimum cycle time that, if used by the host, the CompactFlash Storage Card guarantees data integrity during the transfer.

If this field is supported, bit 1 of word 53 shall be set to one. The value in word 65 shall not be less than the minimum cycle time for the fastest DMA mode supported by the device. This field shall be supported by all CompactFlash Storage Cards supporting DMA modes 1 and above. If bit 1 of word 53 is set to one, but this field is not supported, the Card shall return a value of zero in this field.

¾Recommended Multiword DMA transfer cycle time

Word 66 of the parameter information of the Identify Device command is defined as the recommended Multiword DMA transfer cycle time. This field defines, in nanoseconds, the cycle time that, if used by the host, may optimize the data transfer from by reducing the probability that the CompactFlash Storage Card will need to negate the DMARQ signal during the transfer of a sector.

If this field is supported, bit 1 of word 53 shall be set to one. The value in word 66 shall not be less than the value in word 65. This field shall be supported by all CompactFlash Storage Cards supporting DMA modes 1 and above. If bit 1 of word 53 is set to one, but this field is not supported, the Card shall return a value of zero in this field.

¾Word 67: Minimum PIO transfer cycle time without flow control

Word 67 of the parameter information of the Identify Device command is defined as the minimum PIO transfer without flow control cycle time. This field defines, in nanoseconds, the minimum cycle time that, if used by the host, the CompactFlash Storage Card guarantees data integrity during the transfer without utilization of flow control. If this field is supported, Bit 1 of word 53 shall be set to one. Any CompactFlash Storage Card that supports PIO mode 3 or above shall support this field, and the value in word 67 shall not be less than the value reported in word 68. If bit 1 of word 53 is set to one because a CompactFlash Storage Card supports a field in words 64-70 other than this field and the CompactFlash Storage Card does not support this field, the CompactFlash Storage Card shall return a value of zero in this field.

¾Word 68: Minimum PIO transfer cycle time with IORDY

Word 68 of the parameter information of the Identify Device command is defined as the minimum PIO transfer with IORDY flow control cycle time. This field defines, in nanoseconds, the minimum cycle time that the CompactFlash Storage Card supports while performing data transfers while utilizing IORDY flow control. If this field is supported, Bit 1 of word 53 shall be set to one. Any CompactFlash Storage Card that supports PIO mode 3 or above shall support this field, and the value in word 68 shall be the fastest defined PIO mode supported by the CompactFlash Storage Card. If bit 1 of word 53 is set to one because a CompactFlash Storage Card supports a field in words 64-70 other than this field and the CompactFlash Storage Card does not support this field, the CompactFlash Storage Card shall return a value of zero in this field.

¾Words 82-84: Features/command sets supported

Words 82, 83, and 84 shall indicate features/command sets supported. The value 0000h or FFFFh was placed in each of these words by CompactFlash Storage Cards prior to ATA-3 and shall be interpreted by the host as meaning that features/command sets supported are not indicated. Bits 1 through 13 of word 83 and bits 0 through 13 of word 84 are reserved. Bit 14 of word 83 and word 84 shall be set to one and bit 15 of word 83 and word 84 shall be cleared to zero to provide indication that the features/command sets supported words are valid. The values in these words should not be depended on by host implementers.

Transcend Information Inc.

61

Page 60 Page 62
Image 61
Page 60 Page 62
Contents Dimensions Placement Features266X CompactFlash Card DescriptionTranscend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification „ Output Drive Type „ Output Drive Characteristics „ Signal Interface „ Additional Requirements for CF Advanced Timing Modes „ Ultra DMA Electrical Requirements 266X CompactFlash Card¾ Series termination required for Ultra DMA operation Table Typical Series Termination for Ultra DMA¾ Ultra DMA Mode Cabling Requirement „ Attribute Memory Read Timing Specification TS2G~8GCF266 „ Common Memory Read Timing Specification „ Common Memory Write Timing Specification „ I/O Input Read Timing Specification TS2G~8GCF266 „ I/O Output Write Timing Specification TS2G~8GCF266 „ True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 Table Ultra DMA Data Burst Timing „ True IDE Ultra DMA Mode Read/Write Timing Specification266X CompactFlash Card TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 „ Single Function CF+ Cards Card Configuration„ Multiple Function CF+ Cards TS2G~8GCF266 Attribute Memory Function „ Attribute Memory FunctionTS2G~8GCF266 TS2G~8GCF266 „ Pin Replacement Register Base + 04h in Attribute Memory „ Socket and Copy Register Base + 06h in Attribute Memory Transfer Function Table Pcmcia Mode I/O FunctionTable Common Memory Function Common Memory Transfer FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol Table Primary and Secondary I/O Decoding „ I/O Primary and Secondary Address ConfigurationsTable Contiguous I/O Decoding „ Contiguous I/O Mapped Addressing„ Memory Mapped Addressing „ True IDE Mode Addressing¾ Data Register Address 1F0h170hOffset 0,8,9 „ CF-ATA Registers¾ Sector Number LBA 7-0 Register Address 1F3h173h Offset ¾ Sector Count Register Address 1F2h172h Offset¾ Cylinder High LBA 23-16 Register Address 1F5h175h Offset ¾ Drive/Head LBA 27-24 Register Address 1F6h176h OffsetTS2G~8GCF266 ¾ Device Control Register Address 3F6h376h Offset Eh ¾ Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set „ Check Power Mode 98h or E5h „ Erase Sectors C0h „ Execute Drive Diagnostic 90h„ Format Track 50h „ Flush Cache E7h„ Identify Device Ech 266X CompactFlash Card ¾ Word 0 General Configuration ¾ Word 3 Default Number of Heads ¾ Word 1 Default Number of Cylinders¾ Word 6 Default Number of Sectors per Track ¾ Word 49 Capabilities Bit 13 Standby Timer¾ Total Sectors Addressable in LBA Mode ¾ Multiple Sector Setting¾ Translation Parameters Valid ¾ Current Number of Cylinders, Heads, Sectors/Track¾ Word 65 Minimum Multiword DMA transfer cycle time ¾ Words 82-84 Features/command sets supported¾ Recommended Multiword DMA transfer cycle time ¾ Word 68 Minimum PIO transfer cycle time with Iordy¾ Words 85-87 Features/command sets enabled ¾ Word 89 Time required for Security erase unit completion ¾ Word 88 Ultra DMA Modes Supported and Selected¾ Word 160 Power Requirement Description ¾ Word 91 Advanced power management level value¾ Word 128 Security Status Bit 8 Security Level Additional Requirements for CF Advanced Timing ModesTS2G~8GCF266 „ Idle 97h or E3h „ Initialize Drive Parameters 91h „ Idle Immediate 95h or E1h„ NOP 00h „ Read DMA C8h „ Read Long Sector 22h or 23h „ Read Buffer E4hTS2G~8GCF266 „ Recalibrate 1Xh „ Request Sense 03h „ Seek 7Xh „ Set Features EFh Feature Supported 266X CompactFlash Card Translate Sector Information „ Standby Immediate 94h or E0h „ Translate Sector 87h„ Wear Level F5h „ Write Buffer E8h „ Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 „ Error Posting TS2G~8GCF266
Top Page Image Contents