Transcend Information CF 266X dimensions ¾ Words 85-87 Features/command sets enabled

Page 62

TS2G~8GCF266

266X CompactFlash Card

Bit 0 of word 82 shall be set to zero; the SMART feature set is not supported. If bit 1 of word 82 is set to one, the Security Mode feature set is supported.

Bit 2 of word 82 shall be set to zero; the Removable Media feature set is not supported. Bit 3 of word 82 shall be set to one; the Power Management feature set is supported. Bit 4 of word 82 shall be set to zero; the Packet Command feature set is not supported. If bit 5 of word 82 is set to one, write cache is supported.

If bit 6 of word 82 is set to one, look-ahead is supported.

Bit 7 of word 82 shall be set to zero; release interrupt is not supported. Bit 8 of word 82 shall be set to zero; Service interrupt is not supported.

Bit 9 of word 82 shall be set to zero; the Device Reset command is not supported.

Bit 10 of word 82 shall be set to zero; the Host Protected Area feature set is not supported. Bit 11 of word 82 is obsolete.

Bit 12 of word 82 shall be set to one; the CompactFlash Storage Card supports the Write Buffer command.

Bit 13 of word 82 shall be set to one; the CompactFlash Storage Card supports the Read Buffer command.

Bit 14 of word 82 shall be set to one; the CompactFlash Storage Card supports the NOP command. Bit 15 of word 82 is obsolete.

Bit 0 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Download Microcode command.

Bit 1 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Read DMA Queued and Write DMA Queued commands.

Bit 2 of word 83 shall be set to one; the CompactFlash Storage Card supports the CFA feature set.

If bit 3 of word 83 is set to one, the CompactFlash Storage Card supports the Advanced Power Management feature set.

Bit 4 of word 83 shall be set to zero; the CompactFlash Storage Card does not support the Removable Media Status feature set.

¾Words 85-87: Features/command sets enabled

Words 85, 86, and 87 shall indicate features/command sets enabled. The value 0000h or FFFFh was placed in each of these words by CompactFlash Storage Cards prior to ATA-4 and shall be interpreted by the host as meaning that features/command sets enabled are not indicated. Bits 1 through 15 of word 86 are reserved. Bits 0-13 of word 87 are reserved. Bit 14 of word 87 shall be set to one and bit 15 of word 87 shall be cleared to zero to provide indication that the features/command sets enabled words are valid. The values in these words should not be depended on by host implementers.

Bit 0 of word 85 shall be set to zero; the SMART feature set is not enabled.

If bit 1 of word 85 is set to one, the Security Mode feature set has been enabled via the Security Set Password command.

Bit 2 of word 85 shall be set to zero; the Removable Media feature set is not supported. Bit 3 of word 85 shall be set to one; the Power Management feature set is supported. Bit 4 of word 85 shall be set to zero; the Packet Command feature set is not enabled. If bit 5 of word 85 is set to one, write cache is enabled.

If bit 6 of word 85 is set to one, look-ahead is enabled.

Bit 7 of word 85 shall be set to zero; release interrupt is not enabled. Bit 8 of word 85 shall be set to zero; Service interrupt is not enabled.

Bit 9 of word 85 shall be set to zero; the Device Reset command is not supported.

Bit 10 of word 85 shall be set to zero; the Host Protected Area feature set is not supported. Bit 11 of word 85 is obsolete.

Bit 12 of word 85 shall be set to one; the CompactFlash Storage Card supports the Write Buffer command.

Bit 13 of word 85 shall be set to one; the CompactFlash Storage Card supports the Read Buffer

Transcend Information Inc.

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents 266X CompactFlash Card Placement FeaturesDimensions DescriptionTranscend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification „ Output Drive Type „ Output Drive Characteristics „ Signal Interface „ Additional Requirements for CF Advanced Timing Modes ¾ Series termination required for Ultra DMA operation 266X CompactFlash Card„ Ultra DMA Electrical Requirements Table Typical Series Termination for Ultra DMA¾ Ultra DMA Mode Cabling Requirement „ Attribute Memory Read Timing Specification TS2G~8GCF266 „ Common Memory Read Timing Specification „ Common Memory Write Timing Specification „ I/O Input Read Timing Specification TS2G~8GCF266 „ I/O Output Write Timing Specification TS2G~8GCF266 „ True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 „ True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst Timing266X CompactFlash Card TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 „ Multiple Function CF+ Cards Card Configuration„ Single Function CF+ Cards TS2G~8GCF266 „ Attribute Memory Function Attribute Memory FunctionTS2G~8GCF266 TS2G~8GCF266 „ Pin Replacement Register Base + 04h in Attribute Memory „ Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol „ I/O Primary and Secondary Address Configurations Table Primary and Secondary I/O Decoding„ Contiguous I/O Mapped Addressing Table Contiguous I/O Decoding„ True IDE Mode Addressing „ Memory Mapped Addressing„ CF-ATA Registers ¾ Data Register Address 1F0h170hOffset 0,8,9¾ Cylinder High LBA 23-16 Register Address 1F5h175h Offset ¾ Sector Count Register Address 1F2h172h Offset¾ Sector Number LBA 7-0 Register Address 1F3h173h Offset ¾ Drive/Head LBA 27-24 Register Address 1F6h176h OffsetTS2G~8GCF266 ¾ Device Control Register Address 3F6h376h Offset Eh ¾ Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set „ Check Power Mode 98h or E5h „ Execute Drive Diagnostic 90h „ Erase Sectors C0h„ Flush Cache E7h „ Format Track 50h„ Identify Device Ech 266X CompactFlash Card ¾ Word 0 General Configuration ¾ Word 6 Default Number of Sectors per Track ¾ Word 1 Default Number of Cylinders¾ Word 3 Default Number of Heads ¾ Word 49 Capabilities Bit 13 Standby Timer¾ Translation Parameters Valid ¾ Multiple Sector Setting¾ Total Sectors Addressable in LBA Mode ¾ Current Number of Cylinders, Heads, Sectors/Track¾ Recommended Multiword DMA transfer cycle time ¾ Words 82-84 Features/command sets supported¾ Word 65 Minimum Multiword DMA transfer cycle time ¾ Word 68 Minimum PIO transfer cycle time with Iordy¾ Words 85-87 Features/command sets enabled ¾ Word 88 Ultra DMA Modes Supported and Selected ¾ Word 89 Time required for Security erase unit completion¾ Word 128 Security Status Bit 8 Security Level ¾ Word 91 Advanced power management level value¾ Word 160 Power Requirement Description Additional Requirements for CF Advanced Timing ModesTS2G~8GCF266 „ Idle 97h or E3h „ NOP 00h „ Idle Immediate 95h or E1h„ Initialize Drive Parameters 91h „ Read Buffer E4h „ Read DMA C8h „ Read Long Sector 22h or 23hTS2G~8GCF266 „ Recalibrate 1Xh „ Request Sense 03h „ Seek 7Xh „ Set Features EFh Feature Supported 266X CompactFlash Card „ Standby Immediate 94h or E0h „ Translate Sector 87h Translate Sector Information„ Wear Level F5h „ Write Buffer E8h „ Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 „ Error Posting TS2G~8GCF266
Top Page Image Contents