Transcend Information CF 266X dimensions Idle 97h or E3h

Page 66

TS2G~8GCF266

266X CompactFlash Card

¾Word 164: CF Advanced PCMCIA I/O and Memory Timing Modes Capabilities and Settings

This word describes the capabilities and current settings for CFA defined advanced timing modes using the Memory and PCMCIA I/O interface.

Notice! The use of PCMCIA I/O or Memory modes that are 100ns or faster impose significant restrictions on the implementation of the host:

Additional Requirements for CF Advanced Timing Modes.

Bits 2-0: Maximum Advanced PCMCIA I/O Mode Support Indicates the maximum I/O timing mode supported by the card.

Bits 5-3: Maximum Memory timing mode supported

Indicates the Maximum Memory timing mode supported by the card.

Bits 15-6: Reserved.

Idle - 97h or E3h

This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. If the sector count is non-zero, it is interpreted as a timer count with each count being 5 milliseconds and the automatic power down mode is enabled. If the sector count is zero, the automatic power down mode is disabled. Note that this time base (5 msec) is different from the ATA specification.

Transcend Information Inc.

66

Image 66

Contents 266X CompactFlash Card Placement FeaturesDimensions DescriptionTranscend Block Diagram Pin Assignments and Pin Type TS2G~8GCF266 Signal Description TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Electrical Specification „ Output Drive Type „ Output Drive Characteristics „ Signal Interface „ Additional Requirements for CF Advanced Timing Modes ¾ Series termination required for Ultra DMA operation 266X CompactFlash Card„ Ultra DMA Electrical Requirements Table Typical Series Termination for Ultra DMA¾ Ultra DMA Mode Cabling Requirement „ Attribute Memory Read Timing Specification TS2G~8GCF266 „ Common Memory Read Timing Specification „ Common Memory Write Timing Specification „ I/O Input Read Timing Specification TS2G~8GCF266 „ I/O Output Write Timing Specification TS2G~8GCF266 „ True IDE PIO Mode Read/Write Timing Specification TS2G~8GCF266 „ True IDE Ultra DMA Mode Read/Write Timing Specification Table Ultra DMA Data Burst Timing266X CompactFlash Card TS2G~8GCF266 TS2G~8GCF266 TS2G~8GCF266 Card Configuration „ Single Function CF+ Cards„ Multiple Function CF+ Cards TS2G~8GCF266 „ Attribute Memory Function Attribute Memory FunctionTS2G~8GCF266 TS2G~8GCF266 „ Pin Replacement Register Base + 04h in Attribute Memory „ Socket and Copy Register Base + 06h in Attribute Memory Table Pcmcia Mode I/O Function Transfer FunctionCommon Memory Transfer Function Table Common Memory FunctionTrue IDE Mode I/O Transfer Function Metaformat Overview CF-ATA Drive Register Set Definition and Protocol „ I/O Primary and Secondary Address Configurations Table Primary and Secondary I/O Decoding„ Contiguous I/O Mapped Addressing Table Contiguous I/O Decoding„ True IDE Mode Addressing „ Memory Mapped Addressing„ CF-ATA Registers ¾ Data Register Address 1F0h170hOffset 0,8,9¾ Cylinder High LBA 23-16 Register Address 1F5h175h Offset ¾ Sector Count Register Address 1F2h172h Offset¾ Sector Number LBA 7-0 Register Address 1F3h173h Offset ¾ Drive/Head LBA 27-24 Register Address 1F6h176h OffsetTS2G~8GCF266 ¾ Device Control Register Address 3F6h376h Offset Eh ¾ Card Drive Address Register Address 3F7h377h Offset Fh CF-ATA Command Set „ Check Power Mode 98h or E5h „ Execute Drive Diagnostic 90h „ Erase Sectors C0h„ Flush Cache E7h „ Format Track 50h„ Identify Device Ech 266X CompactFlash Card ¾ Word 0 General Configuration ¾ Word 6 Default Number of Sectors per Track ¾ Word 1 Default Number of Cylinders¾ Word 3 Default Number of Heads ¾ Word 49 Capabilities Bit 13 Standby Timer¾ Translation Parameters Valid ¾ Multiple Sector Setting¾ Total Sectors Addressable in LBA Mode ¾ Current Number of Cylinders, Heads, Sectors/Track¾ Recommended Multiword DMA transfer cycle time ¾ Words 82-84 Features/command sets supported¾ Word 65 Minimum Multiword DMA transfer cycle time ¾ Word 68 Minimum PIO transfer cycle time with Iordy¾ Words 85-87 Features/command sets enabled ¾ Word 88 Ultra DMA Modes Supported and Selected ¾ Word 89 Time required for Security erase unit completion¾ Word 128 Security Status Bit 8 Security Level ¾ Word 91 Advanced power management level value¾ Word 160 Power Requirement Description Additional Requirements for CF Advanced Timing ModesTS2G~8GCF266 „ Idle 97h or E3h „ Idle Immediate 95h or E1h „ Initialize Drive Parameters 91h„ NOP 00h „ Read Buffer E4h „ Read DMA C8h „ Read Long Sector 22h or 23hTS2G~8GCF266 „ Recalibrate 1Xh „ Request Sense 03h „ Seek 7Xh „ Set Features EFh Feature Supported 266X CompactFlash Card „ Standby Immediate 94h or E0h „ Translate Sector 87h Translate Sector Information„ Wear Level F5h „ Write Buffer E8h „ Write DMA CAh TS2G~8GCF266 TS2G~8GCF266 „ Error Posting TS2G~8GCF266