Toshiba IK-WB70A manual Troubleshooting, Status LED, Reboot and restore, Audio

Page 71

Troubleshooting

Status LED

The LED indicates the status of the Network Camera.

Status LED	Description
Blinking red	1.	Power is being supplied to the Network Camera.
(two short, one long)	2.	Restore, or reboot the Network Camera.

Introduction

Reboot and restore

Reset button

Status LED

There is a reset button on the inner side of the Network Camera. It is used to reboot the Network Camera or restore the Network Camera to factory default. Sometimes rebooting the Network Camera could set the Network Camera back to normal state. If the problems remain after rebooting, restore the Network Camera to factory default and install again.

Reboot: Press and release the reset button. The status LED will blink two short one long in red.

Restore: Press the reset button continuously for over 5 seconds until the status LED blinks two short one long in red. Note that all settings will be restored to factory default.

Restoring the factory defaults will erase any previous settings.

Audio

When using multiple network cameras, restart Internet Explorer each time you switch the camera. Using the same Internet Explorer for the multiple cameras may transmit multiple camera's audio.

㪐㪍㩷㪆㩷㪈㪍㪇

Installation

How to Use

Conﬁguration Deﬁnitions

Appendix

71

Image 71

Contents Model IK-WB70A FCC USA-INFORMATION IntroductionTerms and Trademarks Important Safeguards 㪊㪇㩷㪆㩷㪈㪍㪇㪊㪈㩷㪆㩷㪈㪍㪇 Protection of Personal Information Precautions for UseDisclaimer Copyright and Right of PortraitAC adapter AC adapter DSA-20P-10 SpeciﬁcationsTable of Contents Contents General I/O Terminal Block ConnectorsPhysical description Front panelDigital Output Internal Circuit Signal ConditionDigital Input Hardware installation InstallationInternet connection via a gateway Setup the Network Camera over the InternetNetwork deployment Internet connection via PPPoE Point-to-Point over Ethernet Internet connection with static IPWhen using a non-PoE hub Set up the Network Camera through Power over Ethernet PoEWhen using a PoE hub Software installation Using web browsers Initial Access to the Network Camera㪋㪌㩷㪆㩷㪈㪍㪇 MPEG-4 Using 3GPP-compatible mobile devicesCamera Name Main Screen with Camera ViewToshiba Logo MenuLive Video Window 㪋㪐㩷㪆㩷㪈㪍㪇㪌㪇㩷㪆㩷㪈㪍㪇 MPEG-4 Protocol Options Client SettingsStream Options MPEG-4 Media OptionsMP4 Saving Options System Time Conﬁguration DeﬁnitionsSystem Parameters SystemDI and do Manage User Security SettingsRoot Password Add UserHttps Enable HttpsTo create a self-signed certiﬁcate manually Create and Install CertiﬁcateTo install a trusted create certiﬁcate To create a self-signed certiﬁcate automaticallyCertiﬁcate Information Security Alert Network Type NetworkPPPoE Point-to-point over Ethernet 㪍㪉㩷㪆㩷㪈㪍㪇 Http Two way audio HttpsFTP Rtsp Streaming 㪍㪎㩷㪆㩷㪈㪍㪇 Ddns Ddns Dynamic domain name serviceDelete allowed list / Delete denied list Access listAllowed list or Denied list Audio and video Video settingsKeep current value Image SettingsAuto Privacy mask Sensor SettingsIR cut ﬁlter Enable WDR Wide Dynamic Range㪎㪋㩷㪆㩷㪈㪍㪇 Disable IR LED Audio settings Motion detection 㪎㪏㩷㪆㩷㪈㪍㪇 Camera control RS485 SettingsCustom Command Preset Position㪏㪈㩷㪆㩷㪈㪍㪇 Application Media Settings㪏㪊㩷㪆㩷㪈㪍㪇 Server Settings 㪏㪌㩷㪆㩷㪈㪍㪇㪏㪍㩷㪆㩷㪈㪍㪇 Event 㪏㪏㩷㪆㩷㪈㪍㪇 Recording Recording Settings㪐㪇㩷㪆㩷㪈㪍㪇 Current Log System logView parameters Remote LogRestore MaintenanceReboot Upload or Export Daylight Saving Time Conﬁguration File Upgrade Firmware 㪐㪌㩷㪆㩷㪈㪍㪇 Audio TroubleshootingReboot and restore Status LEDWrong date and time Daylight Saving Time DST Glossary IndexUse Deﬁnitions Conﬁguration AWB SpeciﬁcationsAppearance Diagram 㪈㪇㪉㩷㪆㩷㪈㪍㪇 AMR-NB Standard Technology License NoticeMPEG-4 AAC Technology MPEG-4 Visual TechnologyGNU General Public License 㪈㪇㪌㩷㪆㩷㪈㪍㪇 No Warranty END of Terms and Conditions Toshiba America Information SYSTEMS, INC