Toshiba IK-TF5U instruction manual Components

Page 5

( 3 ) Trigger Pulse Specifications

32

( 2 ) Vertical Output Waveform Timing Chart ...

33

( 4 ) External HD/VD Input Phase

 

10.

SPECIFICATIONS

34

Specifications

32

11.

EXTERNAL APPEARANCE DIAGRAM

35

9. CCD OUTPUT WAVEFORM TIMING CHART ....

33

12.

BEFORE MAKING A SERVICE CALL

35

( 1 ) Horizontal Output Waveform Timing Chart ...

33

This product is 3CCD color camera with digital video output.

1. CAUTIONS ON USE AND INSTALLATION

Handling the unit.

Do not drop, jolt, or vibrate, as this may result in damage to the unit. This may cause problems. Treat the camera cables carefully to prevent cable problems, such as breaks in the cable and loose connections.

Install the camera in a location free from noise.

If the camera or the cables are located near power utility lines or a TV, etc. undesirable noise may appear on the screen. In such a case, try to change the location of the camera or the cable wiring.

Operating ambient temperature and humidity. Do not use the camera in places where tempera- ture and humidity exceed the specifications. Pic- ture quality will deteriolate and internal parts may be damaged.

Be particularly careful when using in places ex- posed to direct sunlight. When shooting in hot places, depending on the conditions of the object and the camera (for example when the gain is in- creased), noise in the form of vertical strips or white dots may occur. This is not a malfunction.

When not using the camera for extended peri- ods of time.

Switch the control unit off and disconnect the power supply.

Avoid using or storing the camera in the fol- lowing places:

Places filled with highly flammable and corrosive gas.

Places near gasoline, benzene, or paint thinner. Places subject to strong vibration.

Places containing chemicals (such as pesticides), rubber or vinyl products for extended periods of time.

The following descriptions are for that a camera head “IK-TF5H” connected to this camera control unit.

Do not shoot intense light.

If there is an intense light at a location on the screen such as a spot light, a blooming and smear- ing may occur. When intense light enters, vertical stripes may appear on the screen. This is not a malfunction. Ghosts may occur when there is an intense light near the object. In this case, change the shooting angle.

Moire

A moire pattern is an interference pattern gener- ated when two repetitive line patterns overlap. This is not a malfunction. Eliminating the repetitive line patterns, or aligning the two patterns, will elimi- nate the moire.

Handling of the camera head and protection cap.

Keep the camera head and protection cap away from as they may pose a choking hazard. The pro- tection cap protects the image sensing plane when the lens is removed from the camera head, do not discard.

When cleaning the camera.

Unplug the power source before cleaning. Clean with a soft dry cloth only. Do not use chemicals or chemically treated cloths. Chemicals may damage coatings and printed letters. When cleaning the lens, use lens cleaning paper.

Installation without a tripod.

Before installing the camera head and the cam- era control unit, make sure that the location can withstand the total weight of the camera head and the camera control unit.

If this is not the case, reinforce the area to pre- vent the unit from dropping, which may result in damage to the unit or personal injury.

2. COMPONENTS

 

(1)

Camera Control Unit

1

(2)

Accessories

 

 

(a) Instruction manual

1

5

Image 5
Contents Following information is only for EU-member states IK-TF5USafety Precautions Avoid placing in humid, smoky, vaporized or dusty places DisclaimerTable of Contents Components Names and Functions Standard Connection Connector Pin AssignmentsConnection White Balance OperationAutomatic Black Balance Temp LOW Result displayed MeaningOFF GainShading Correction Available selections Items Controlled by the Screen DisplayDisp Mode Setting by the Screen DisplayUsing the Menus Shutter Electronic shutter MenusManual Flicker may be largeMode = Manual Changing the setting in Manu modePartial scanning setting Menu UP, Down Data UP, DownChanging the shutter speed setting Changing the setting in SS synchro. scan modeMode = SS Changing the setting in 1P SNR mode Changing the setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging 1P SR exposure time setting Changing the setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Mode = E.TRG E.TRG = PW SNR Changing the setting in PW SNR modeMode = E.TRG E.TRG = RR Changing the setting in PW SR modeMode = E.TRG E.TRG = PW SR Gain Video gain Changing the setting in GainChanging the gain in Manu mode WHT BAL White balance Changing gamma correction MANU/OFFChanging master pedestal Changing R pedestalOption SyncReturning to factory settings Setting by the frameSetting by 1H Synchro. Scan Operation1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetE. TRG External trigger Fval Lval Dval1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETLong Term Exposure RR Reset restartInput Timing Chart Example Partial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onUsing the unit with external sync signal External sync signal polarityExternal Sync External sync frequency rangeInput Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart RGB, 3CCD SpecificationsSymptom Items to be checked External Appearance DiagramBefore Making a Service Call One 1 Year Limited Warranty of Labor and Parts Limited Warranty Toshiba CCD CameraHow to Obtain Warranty Service Step-By-Step Procedures Your Responsibilities