Toshiba IK-TF5U instruction manual Sync, Option

Page 23

(4. 5) Changing the shading correction mode

1Move the "→" to SHAD. by pushing [MENU UP], [MENU DOWN] buttons.

2Select the SHAD. by pushing [DATA UP], [DATA DOWN] buttons.

Note: The alignment value for shading is fixed to "0" when selecting SHAD. OFF. MANU is not dis- played in the menu.

(4. 6) Changing the manual shading correction setting

1Move the "→" to MANU by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.

( 5 ) SYNC

When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically.

Move up down

Select the desired

by pushing

value by pushing

MENU UP, DOWN

DATA UP, DOWN

-- SYNC --

MODE

EXT

H PHASE

0

•Sync system display

•H PHASE adjustment -100 to 100

(5. 1) Adjusting horizontal phase

1Move the "→" to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.

( 6 ) OPTION

(6. 1) Changing serial communication baud rate

1Move the "→" to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.

2Select either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.

Move up down by pushing

MENU UP, DOWN

Select the desired value by pushing

DATA UP, DOWN

-- OPTION --

BAUD RATE 9600

• Serial baud rate setting 9600, 19200

23

Image 23

Contents Following information is only for EU-member states IK-TF5USafety Precautions Avoid placing in humid, smoky, vaporized or dusty places DisclaimerTable of Contents Components Names and Functions Standard Connection Connector Pin AssignmentsConnection White Balance OperationAutomatic Black Balance Temp LOW Result displayed MeaningOFF GainShading Correction Available selections Items Controlled by the Screen DisplayDisp Mode Setting by the Screen DisplayUsing the Menus Flicker may be large MenusShutter Electronic shutter ManualMenu UP, Down Data UP, Down Changing the setting in Manu modeMode = Manual Partial scanning settingChanging the shutter speed setting Changing the setting in SS synchro. scan modeMode = SS Changing 1P SNR exposure time setting Changing the setting in E.TRG modeChanging the setting in 1P SNR mode Changing the polarity of inputting trigger pulse settingChanging 1P SR exposure time setting Changing the setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Mode = E.TRG E.TRG = PW SNR Changing the setting in PW SNR modeMode = E.TRG E.TRG = RR Changing the setting in PW SR modeMode = E.TRG E.TRG = PW SR Gain Video gain Changing the setting in GainChanging the gain in Manu mode WHT BAL White balance Changing R pedestal MANU/OFFChanging gamma correction Changing master pedestalOption SyncSynchro. Scan Operation Setting by the frameReturning to factory settings Setting by 1HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing E. TRG External trigger1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETLong Term Exposure RR Reset restartInput Timing Chart Example Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningExternal sync frequency range External sync signal polarityUsing the unit with external sync signal External SyncInput Output Signal Specificatoins Vertical Output Waveform Timing Chart CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart RGB, 3CCD SpecificationsSymptom Items to be checked External Appearance DiagramBefore Making a Service Call Your Responsibilities Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts How to Obtain Warranty Service Step-By-Step Procedures