Toshiba IK-TF7 Synchro. Scan Operatin, Setting by the frame, Changing HD/VD input/output

Page 23

( 3 ) Using the unit with external sync signal

When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase".

(3. 1) H (horizontal) phase adjustment

Observe the external sync signal and the video signal output waveform of the unit with a dual trace oscilloscope, and ad- just H phase so that the H phases match.

External

Sync. signal Match

the phase.

Camera

Video output

( 4 ) Changing HD/VD input/output

(1)Put off 6 screws both on flank/top of camera chassis.

(2)Change internal switch SJ01(HD/VD).

HD/VD OUTPUT

SJ01

HD/VD INPUT high-impedance HD/VD INPUT 75Ω (factory setting)

7. 4 Synchro. Scan Operatin

The shutter speed can be set by the horizontal scanning period (1H) or by the frame.

( 1 ) Setting by 1H

1H/796H to 795H/796H (1H/387H to 386H/387H when partial scanning at 60fps, 1H/258H to 257H/258H when partial scanning at 90fps) stands for the setting by the 1H and the shutter speed can be set by the 1H (43.05

µs).

( 2 ) Setting by the frame

2FRM to 512FRM stand for the setting (long period exposure) by the frame.

The video signal stored during the frame period set is output as 1 frame video image at a frame interval specified.

VD output

Video putput

Index output

(INDEX)

n

(4FRM setting)

n+1

23

IK-TF7(E)

Page 23

2004.03.24, 0:59 PMAdobe PageMaker 6.5J/PPC

Image 23

Contents For Customer Use IK-TF7Safety Precautions Disclaimer Table of Contents Components Available selectins Items Controlled by Using on Screen DisplayNames and Functions Standard Connection Connector Pin AssignmentsConnection Result displayed Meaning OperationWhite Balance Automatic White Balance Manual White Balance OutlineOFF Shutter speed mode is E.TRG modeGain Shading CorrectionDisp Mode Setting by on Screen DisplayUsing the Menues Power onShutter Electronic shutter Changing each setting in Manu modePartial scanning setting MenusChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeChanging the gain in Manu mode Changing each setting in RR modeMode = E.TRG E.TRG = RR Changing each setting in GainWHT BAL White balance Changing B pedestal Changing shading correction modeChanging master pedestal Changing R pedestalChanging RGB Sync Adjusting horizontal phaseSync OptionExternal Sync Setting to factory setting statusExternal sync signal input conditions Shutter mode HD input VD inputSynchro. Scan Operatin Setting by the frameUsing the unit with external sync signal Setting by 1HEXT Trig External trigger 1P SNR 1 Pulse Trigger Sync Non ResetVD OUT*3 Video Index VD OUT 1P SR 1 Pulse Trigger Sync Reset1 Pulse Trigger SYNC-RESET Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset VD OUT Video Index VD OUT*3 PW SR Pulse width trigger SYNC-RESET1 Pulse Width Trigger SYNC-RESET Picture Output Timing Video OUT Video Index RR Reset restartInput Timing Chart Example Long Term ExposurePartial Scanning on When Partial Scanning Mode is onPartial Scanning Partial Scanning OFF All pixels scanningInput Output Signal Specificatoins CCD CCD Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Vertical Output Waveform Timing ChartHD, VD, Index SpecificationsRGB, 3CCD Symptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service