Toshiba IK-TF7 instruction manual Standard Connection, Connector Pin Assignments

Page 8

5.CONNECTION

5.1 Standard Connection

Lens

IK-TF7

Less than 4 mm

Camera cable
(option)	RGB
DC IN 12V	Image processing
	Image processing
DC power supply	equipments, etc.
DC power supply

5. 2 Cautions on Connection

•When connecting the camera cables, be sure to turn off the camera and the other equipment connected.

•We suggest using a C mount lens made for a 3CCD camera.

When using another lens, the best camera performance of this camera may not be obtained.

(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and flare, ghost or shading may occur)

Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens which has projection dimension from the mounting base of less than 0.157"(4mm).

•For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounding type AC adaptor with the specifications described below.

Power supply voltage	: DC12V± 10%
Current rating	: More than 830 mA
Ripple voltage	: Less than 50 mV(p–p)
Connector	: HR10A–7P–4S by HIROSE electronics Co. Ltd
	Pins 1, 2	: 12V
	Pins 3, 4	: GND

5. 3 Connector Pin Assignments

DC IN 12V

1+12V

2+12V

3GND

1 3

4

GND

2 4

8

RGB

1R

2G

3B

4TXD

5GND

6GND

7GND

8SYNC

912V

10GND

11RXD

12TRIG

13HD IN/OUT

14VD IN/OUT

15INDEX

5 4 3 2 1

10 9 8 7 6

15 14 13 12 11

IK-TF7(E)

Page 8

2004.03.24, 0:59 PMAdobe PageMaker 6.5J/PPC

Image 8

Contents IK-TF7 For Customer UseSafety Precautions Disclaimer Table of Contents Components Items Controlled by Using on Screen Display Available selectinsNames and Functions Standard Connection Connector Pin AssignmentsConnection Operation White BalanceAutomatic White Balance Manual White Balance Outline Result displayed MeaningShutter speed mode is E.TRG mode GainShading Correction OFFMode Setting by on Screen Display Using the MenuesPower on DispChanging each setting in Manu mode Partial scanning settingMenus Shutter Electronic shutterChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing each setting in E.TRG mode Changing each setting in 1P SNR modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Changing each setting in PW SNR mode Mode = E.TRG E.TRG = PW SNRChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRChanging each setting in RR mode Mode = E.TRG E.TRG = RRChanging each setting in Gain Changing the gain in Manu modeWHT BAL White balance Changing shading correction mode Changing master pedestalChanging R pedestal Changing B pedestalAdjusting horizontal phase SyncOption Changing RGB SyncSetting to factory setting status External sync signal input conditionsShutter mode HD input VD input External SyncSetting by the frame Using the unit with external sync signalSetting by 1H Synchro. Scan Operatin1P SNR 1 Pulse Trigger Sync Non Reset EXT Trig External triggerVD OUT*3 Video Index VD OUT 1P SR 1 Pulse Trigger Sync Reset1 Pulse Trigger SYNC-RESET Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset VD OUT Video Index VD OUT*3 PW SR Pulse width trigger SYNC-RESET1 Pulse Width Trigger SYNC-RESET Picture Output Timing RR Reset restart Input Timing Chart ExampleLong Term Exposure Video OUT Video IndexWhen Partial Scanning Mode is on Partial ScanningPartial Scanning OFF All pixels scanning Partial Scanning onInput Output Signal Specificatoins CCD Output Waveform Timing Chart Horizontal Output Waveform Timing ChartVertical Output Waveform Timing Chart CCDHD, VD, Index SpecificationsRGB, 3CCD Symptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service