Toshiba IK-TF7 instruction manual Input Output Signal Specificatoins

Page 32

8. INPUT OUTPUT SIGNAL SPECIFICATOINS

( 1 ) HD/VD Output Amplitude Specifications

HD 4.5V

0V

VD 4.5V

0V

The amplitude level is the representative value when terminated with 10kΩ .

Output is enabled when the internal switch SJ01 is set to the OUT side.

( 4 ) HD Input Specifications

2.0 to

5.0 V(p-p)

5H to 21H

* Input impedance: 75Ω or 10kΩ or greater

*Input amplitude 2.0 to 5.0 Vp-p (75Ω termination ON or OFF)

*Voltage and pulse width were measured at RGB con- nector located on the rear panel.

2.0 to

( 5 ) Trigger Pulse Specifications

5.0 V(p-p)

2.0 µ s to 5.0 µ s

( 2 ) VD Input Specifications

* Input impedance: 75W or 1kΩ or greater

* Input amplitude 2.0 to 5.0 V(p-p) (75Ω termination ON

or OFF)

* Voltage and pulse width were measured at RGB con-

nector located on the rear panel.

More than 2 µ s

More than 2 µ s

2 5.0V

0 0.4V

(Positive polarity mode)

2 5.0V

0 0.4V

(Negative polarity mode)

4.5V

0V

796H (Partial scanning OFF)

387H (Partial scanning 60fps)

258H (Partial scanning 90fps)

*Input impedance: 10kΩ or greater

*Voltage and pulse width were measured at RGB connector located on the rear panel.

( 3 ) VIDEO INDEX Output Specifications

The amplitude level is the representative value when terminated with 10kW.

( 6 ) External HD/VD Input Phase Specifications

External HD rising edge

100

External HD

100

Unit : Clock

1 clk=33.9nsec

Center

The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD falling edge) as illustrated in the above diagram.

External VD falling edge:

Please input within about 100 clock cycles of the standard center phase.

Note that V sync of the video is output with a delay of about 1H from the external VD at the time of reset-restart and the external trigger mode.

In the normal mode:

Continuously with the HD period of 43.05 µ s and VD period of 34.27 ms (partial scanning 60fps: 16.67 ms, partial

scanning 90fps: 11.11 ms ).

Phase timing is as illustrated in the above diagram (with only the falling edge applicable).

In the reset-restart/external trigger mode:

Continuously with the HD period of 43.05 µ s. VD (reset) is at an arbitrary timing with the phase of HD being within the standard of the above diagram.

32

IK-TF7(E)

Page 32

2004.03.24, 0:59 PMAdobe PageMaker 6.5J/PPC

Page 31 Page 33
Image 32
Page 31 Page 33
Contents IK-TF7 For Customer UseSafety Precautions Disclaimer Table of Contents Components Items Controlled by Using on Screen Display Available selectinsNames and Functions Standard Connection Connector Pin AssignmentsConnection Operation White BalanceAutomatic White Balance Manual White Balance Outline Result displayed MeaningShutter speed mode is E.TRG mode GainShading Correction OFFMode Setting by on Screen Display Using the MenuesPower on DispChanging each setting in Manu mode Partial scanning settingMenus Shutter Electronic shutterChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing each setting in E.TRG mode Changing each setting in 1P SNR modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Changing each setting in PW SNR mode Mode = E.TRG E.TRG = PW SNRChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRChanging each setting in RR mode Mode = E.TRG E.TRG = RRChanging each setting in Gain Changing the gain in Manu modeWHT BAL White balance Changing shading correction mode Changing master pedestalChanging R pedestal Changing B pedestalAdjusting horizontal phase SyncOption Changing RGB SyncSetting to factory setting status External sync signal input conditionsShutter mode HD input VD input External SyncSetting by the frame Using the unit with external sync signalSetting by 1H Synchro. Scan Operatin1P SNR 1 Pulse Trigger Sync Non Reset EXT Trig External triggerVD OUT*3 Video Index VD OUT 1P SR 1 Pulse Trigger Sync Reset1 Pulse Trigger SYNC-RESET Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset VD OUT Video Index VD OUT*3 PW SR Pulse width trigger SYNC-RESET1 Pulse Width Trigger SYNC-RESET Picture Output Timing RR Reset restart Input Timing Chart ExampleLong Term Exposure Video OUT Video IndexWhen Partial Scanning Mode is on Partial ScanningPartial Scanning OFF All pixels scanning Partial Scanning onInput Output Signal Specificatoins CCD Output Waveform Timing Chart Horizontal Output Waveform Timing ChartVertical Output Waveform Timing Chart CCDHD, VD, Index SpecificationsRGB, 3CCD Symptom Items to be checked External Appearance DiagramBefore Making a Service Call Imaging Systems Division Limited One 1 Year Warranty of Labor and PartsStep-by-step Procedures How to Obtain Warranty Service
Top Page Image Contents