Toshiba IK-TF7 instruction manual For Customer Use

Page 1

INSTRUCTION MANUAL

3 CCD CAMERA

IK-TF7

For Customer Use

Enter below the Serial No. w h i c h i s l o c a t e d o n t h e bottom of the cabinet. Retain this information for future ref- erence.

Model No.: IK-TF7

Serial No.:

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursu- ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part 15 of the FCC Rules.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.

IK-TF7(E)

Page 1

2004.03.24, 0:58 PMAdobe PageMaker 6.5J/PPC

Image 1

Contents For Customer Use IK-TF7Safety Precautions Disclaimer Table of Contents Components Available selectins Items Controlled by Using on Screen DisplayNames and Functions Connection Connector Pin AssignmentsStandard Connection White Balance OperationAutomatic White Balance Manual White Balance Outline Result displayed MeaningGain Shutter speed mode is E.TRG modeShading Correction OFFUsing the Menues Mode Setting by on Screen DisplayPower on DispPartial scanning setting Changing each setting in Manu modeMenus Shutter Electronic shutterMode = SS Changing each setting in SS synchro. scan modeChanging the shutter speed setting Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingMode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting Mode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeMode = E.TRG E.TRG = RR Changing each setting in RR modeChanging each setting in Gain Changing the gain in Manu modeWHT BAL White balance Changing master pedestal Changing shading correction modeChanging R pedestal Changing B pedestalSync Adjusting horizontal phaseOption Changing RGB SyncExternal sync signal input conditions Setting to factory setting statusShutter mode HD input VD input External SyncUsing the unit with external sync signal Setting by the frameSetting by 1H Synchro. Scan OperatinEXT Trig External trigger 1P SNR 1 Pulse Trigger Sync Non ResetVD OUT*3 Video Index 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetVD OUT PW SNR Pulse width trigger SYNC-NON Reset VD OUT Video Index 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETVD OUT*3 Input Timing Chart Example RR Reset restartLong Term Exposure Video OUT Video IndexPartial Scanning When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onInput Output Signal Specificatoins Horizontal Output Waveform Timing Chart CCD Output Waveform Timing ChartVertical Output Waveform Timing Chart CCDRGB, 3CCD SpecificationsHD, VD, Index Before Making a Service Call External Appearance DiagramSymptom Items to be checked Step-by-step Procedures How to Obtain Warranty Service Limited One 1 Year Warranty of Labor and PartsImaging Systems Division